200-301 Exam Questions
1,744 real 200-301 exam questions with expert-verified answers and explanations. Page 18 of 35.
- Question #875Network Fundamentals
Drag and Drop Question Drag and drop the IPv6 address types from the left onto their description on the right. Answer:
IPv6 AddressingGlobal UnicastLink-Local UnicastMulticast - Question #876Network Fundamentals - Understanding the characteristics and differences between TCP and UDP transport layer protocols (CompTIA Network+/CCNA Domain: Network Fundamentals)
Drag and Drop Question Drag and drop the characteristics of transport layer protocols from the left onto the corresponding protocols on the right. Answer:
TCPUDPTransport LayerOSI Model - Question #877
A network engineer must configure an interface with IP address 10.10.10.145 and a subnet mask equivalent to 11111111.11111111.11111111.11111000. Which subnet mask must the engineer...
SubnettingCIDR notationBinary subnet mask - Question #878
Refer to the exhibit. The switches are connected via a Cat5 Ethernet cable that is tested successfully. The interfaces are configured as access ports and are both in a down status....
Ethernet link troubleshootingSwitch port speedAuto-negotiationInterface status - Question #879
Which two IP addressing schemes provide internet access to users on the network while preserving the public IPv4 address space? (Choose two.)
IPv6 AddressingNAT/PATPrivate IP Ranges - Question #880IP Connectivity
The address block 192.168.32.0/24 must be subnetted into smaller networks. The engineer must meet these requirements: - Create 8 new subnets. - Each subnet must accommodate 30 host...
IP SubnettingLayer 3 Interface ConfigurationVLAN InterfaceSwitchport Commands - Question #881IP Connectivity
What are two reasons to deploy private addressing on a network? (Choose two.)
Private IP addressingNetwork addressingNetwork segmentation - Question #882Network Fundamentals
Which property is shared by 10GBase-SR and 10GBase-LR interfaces?
10 Gigabit Ethernetfiber opticsphysical layer mediaEthernet standards - Question #883
What is a function spine-and-leaf architecture?
Spine-and-leaf architectureData center networkingNetwork topology - Question #884Network Fundamentals
What is the function of the control plane?
Control planeRouting protocolsRouting table - Question #886Understanding wireless deployment architectures including Lightweight Access Point Protocol (LWAPP) Layer 2 and Layer 3 modes, their encapsulation methods, addressing requirements, and supported transport mechanisms - typically covered under Wireless Network Design and Infrastructure in CCNP Enterprise or CWNA certification objectives.
Drag and Drop Question Drag and drop the statements about wireless architectures from the left onto the architectures on the right. Answer:
Wireless LAN ArchitectureLWAPPLayer 2 vs Layer 3 LWAPPWireless Controller - Question #887Network Access
Refer to the exhibit. Which configuration establishes a Layer 2 LACP EtherChannel when applied to both switches?
EtherChannelLACP configurationSwitchport trunk mode - Question #888
Refer to the exhibit. Which action must be taken so that neighboring devices rapidly discover switch Cat9300?
Cisco CDPCDP configurationNetwork discoveryCisco switch management - Question #889CompTIA Network+ / CCNA - Network Management and Security: Understanding in-band vs. out-of-band management connection types and their security characteristics
Drag and Drop Question Drag and drop the management connection types from the left onto the definitions on the right. Answer:
Network ManagementDevice Access MethodsRemote Access ProtocolsNetwork Security - Question #890Network Access
Refer to the exhibit. An engineer must configure the interface that connects to PC1 and secure it in a way that only PC1 is allowed to use the port. No VLAN tagging can be used exc...
Cisco switchport configurationSwitchport access modePort security concepts - Question #891
Refer to the exhibit. The EtherChannel is configured with a speed of 1000 and duplex as full on both ends of channel group 1. What is the next step to configure the channel on swit...
EtherChannelLACPLACP modesCisco switching - Question #892Network Access
Refer to the exhibit. Switch AccSw1 has just been added to the network along with PC2. All VLANs have been implemented on AccSw2. How must the ports on AccSw2 be configured to esta...
VLAN port configurationSwitch access portsLayer 2 connectivity - Question #893Network Access
Refer to the exhibit. Two new switches are being installed. The remote monitoring team uses the support network to monitor both switches. Which configuration is the next step to es...
Layer 2 connectivitySwitch interface configurationEthernet interfaces - Question #895
Refer to the exhibit. The network engineer is configuring a new WLAN and is told to use a setup password for authentication instead of the RADIUS servers. Which additional set of t...
WLAN configurationWPA2-PSKWireless authenticationPMF - Question #896
Refer to the exhibit. The entire MAC address table for SW1 is shown here: What does SW1 do when Br-4 sends a frame for Br-2?
Ethernet switchingMAC address tableframe forwarding - Question #897Network Access
Refer to the exhibit. The entire Marketing-SW1 MAC address table is shown here: What does the switch do when PC-4 sends a frame to PC-1?
Switch MAC learningFrame forwardingLayer 2 switching - Question #898Network Access
Refer to the exhibit. Which switch becomes the root of a spanning tree for VLAN 10 if the primary switch fails and all links are of equal speed?
STPRoot Bridge ElectionPVST+Network Convergence - Question #899Cisco ENCOR (350-401) - Wireless Infrastructure: Understanding Cisco AP operational modes including Monitor, Sniffer, SE-Connect, Rogue Detector, Bridge, Flex+Bridge, and their specific use cases in enterprise wireless deployments.
Drag and Drop Question Drag and drop the statements about access-point modes from the left onto the corresponding modes on the right. Answer:
Wireless AP ModesCisco Access PointsWLAN ArchitectureRF Management - Question #900IP Connectivity
Refer to the exhibit. A packet sourced from 10.10.10.1 is destined for 10.10.8.14. What is the subnet mask of the destination route?
SubnettingIP addressingRouting table lookupPacket forwarding - Question #9013.0 IP Connectivity
Refer to the exhibit. When an administrator executes the show ip route command on router D to view its routing table, which value is displayed for the administrative distance for t...
Administrative DistanceRouting TableOSPFshow ip route - Question #902IP Connectivity
Refer to the exhibit. Which interface is chosen to forward traffic to the host at 192.168.0.55?
IP routingRouting table lookupPacket forwarding - Question #903IP Connectivity
Refer to the exhibit. Router OldR is replacing another router on the network with the intention of having OldR and R2 exchange routes. After the engineer applied the initial OSPF c...
OSPF configurationOSPF neighbor adjacencyOSPF troubleshooting - Question #904Network Fundamentals – Understand IP addressing and subnetting, including the relationship between dotted-decimal subnet masks and CIDR prefix lengths (CCNA 200-301 Domain 1)
Drag and Drop Question Refer to the exhibit. Drag and drop the prefix lengths from the left onto the corresponding prefixes on the right. Not all prefixes are used. Answer:
Subnet MasksCIDR NotationIPv4 AddressingBinary Conversion - Question #905Network Fundamentals
Refer to the exhibit. What is the subnet mask for route 172.16.4.0?
IP SubnettingSubnet MasksIPv4 Addressing - Question #906
Refer to the exhibit. The network engineer is configuring router R2 as a replacement router on the network. After the initial configuration is applied, it is determined that R2 fai...
OSPF neighbor adjacencyOSPF configurationOSPF troubleshooting - Question #907IP Connectivity
Refer to the exhibit. The router R1 is in the process of being configured. Routers R2 and R3 are configured correctly for the new environment. Which two commands must be configured...
Static routingCisco IOS commandsIP routing configurationNext-hop routing - Question #908IP Connectivity
Refer to the exhibit. Traffic from R1 to the 10.10.2.0/24 subnet uses 192.168.1.2 as its next hop. A network engineer wants to update the R1 configuration so that traffic with dest...
Static routingCisco IOS commandsRoute specificity - Question #909IP Connectivity
Refer to the exhibit. The image server and client A are running an application that transfers an extremely high volume of data between the two. An engineer is configuring a dedicat...
Static routingHost routeNext-hop IP - Question #910
Refer to the exhibit. An engineer is checking the routing table in the main router to identify the path to a server on the network. Which route does the router use to reach the ser...
Routing table lookupLongest prefix matchIP routing - Question #911IP Connectivity
Refer to the exhibit. What is the prefix length for the route that router1 will use to reach host A?
IP routingLongest prefix matchPrefix lengthRouting table - Question #912IP Connectivity
Refer to the exhibit. After applying this configuration to router R1, a network engineer is verifying the implementation. If all links are operating normally, and the engineer send...
IP routingPacket forwardingRouting table lookup - Question #913Network Fundamentals
A switch has 48 ports and 4 VLANs. How many collision and broadcast domains exist on the switch (collision, broadcast)?
Collision DomainsBroadcast DomainsVLANsSwitching Concepts - Question #914IP Connectivity
An engineer just installed network 10.120.10.0/24. Which configuration must be applied to the R14 router to add the new network to its OSPF routing table?
OSPF configurationOSPF network commandWildcard masks - Question #915IP Connectivity
Refer to the exhibit. Router R1 is added to the network and configured with the 10.0.0.64/26 and 10.0.20.0/26 subnets. However, traffic destined for the LAN on R3 is not accessible...
Static routingCisco IOS routingSubnettingIP addressing - Question #916Network Management and Monitoring – understanding the SNMP fault management process and the FCAPS (Fault, Configuration, Accounting, Performance, Security) model, typically tested in certifications such as Cisco CCNP, CompTIA Network+, or Juniper JNCIA/JNCIS.
Drag and Drop Question Drag and drop the functions of SNMP fault-management from the left onto the definitions on the right. Answer:
SNMPFault ManagementFCAPSNetwork Management - Question #917IP Services
Refer to the exhibit. Which router or router group are NTP clients?
NTPNTP clientCisco NTP configuration - Question #918
Refer to the exhibit. What is the next step to complete the implementation for the partial NAT configuration shown?
Cisco NAT configurationNAT interface configurationNAT implementation steps - Question #919IP Services
Refer to the exhibit. A newly configured PC fails to connect to the internet by using TCP port 80 to
DNS troubleshootingClient network configurationInternet connectivity - Question #920Security Fundamentals - Understanding AAA (Authentication, Authorization, and Accounting) framework and its components, typically found in Cisco CCNA or CompTIA Security+ certification objectives.
Drag and Drop Question Drag and drop the statements about AAA from the left onto the corresponding AAA services on the right. Not all options are used. Answer:
AAANetwork SecurityRADIUSTACACS+ - Question #922Security Fundamentals
Refer to the exhibit. An engineer is updating the management access configuration of switch SW1 to allow secured, encrypted remote configuration. Which two commands or command sequ...
Cisco VTY configurationLocal user authenticationSecure network management - Question #923
Refer to the exhibit. What is identified by the word `switch` within line 2 of the JSON Schema?
JSON syntaxJSON keysJSON structure - Question #924Automation and Programmability
Refer to the exhibit. Which type of JSON data is shown?
JSONJSON data types - Question #925Network Automation and Programmability - understanding the differences between configuration management tools (Puppet, Chef) and orchestration tools (Ansible) and their respective roles in automating network and infrastructure operations.
Drag and Drop Question Drag and drop the characteristics from the left onto the technology types on the right. Answer:
Configuration ManagementOrchestrationAutomation ToolsInfrastructure as Code - Question #926Network Fundamentals / Application Layer Protocols - understanding RESTful API communication methods used in modern web and cloud infrastructure, commonly tested in CompTIA Network+, CompTIA Cloud+, and developer certification exams.
Drag and Drop Question Drag and drop the REST API call methods for HTTP from the left onto the actions they perform on the right. Not all methods are used. Answer:
REST APIHTTP MethodsCRUD OperationsWeb Services - Question #927Understanding RESTful API architectural principles and constraints, typically covered in API development, cloud integration, or web services certification domains (e.g., MuleSoft, AWS, CompTIA Cloud+, or API-focused exams).
Drag and Drop Question Drag and drop the REST principles from the left onto their definitions on the right. Answer:
REST principlesAPI designweb servicesarchitectural constraints