352-001 Exam Questions
775 real 352-001 exam questions with expert-verified answers and explanations. Page 11 of 16.
- Question #526Layer 3 Control Plane
At which two networks points is route summarization supported? (Choose two)
route summarizationEIGRP interface boundaryOSPF area boundaryrouting protocol - Question #527Designing Network Services
An enterprise customer will deploy a centralized unified communications application to provide voice, video, and instant messaging to their branch offices. Some of the branch offic...
VoIPWAN bandwidthG.729 codecVAD - Question #528Layer 2 Control Plane
Refer to the exhibit. This layer 2 network is expected to add 150 VLANS over the next year, In addition to the existing 50 VLANs within the network which STP types will support thi...
MSTSTPVLAN scalabilityload balancing - Question #529Design Considerations
You are solving a design failure on a massive Hadoop cluster network that has an application with TCP incast behavior (also known as TCP Throughput collapse) affecting its many-to-...
TCP incastbuffer utilizationdata center networkingthroughput collapse - Question #531Layer 2 Control Plane
Refer to the exhibit. You are designing a data center migration from one location to another, which requires all existing VLANs spanned to the new data center to maintain host IP a...
BPDU filteringfault isolationVLAN extensiondata center migration - Question #532Layer 3 Control Plane
A BGP route reflector in the network is talking longer than expected to converge during network changes. Troubleshooting has shown that the router cannot handle all the TCP acknowl...
BGProute reflectorhold queueTCP performance tuning - Question #533Designing Security
ACME Agricultural requires that access to all network devices is granted based on identify validation, and an authentication server was installed for this purpose. Currently the ne...
LDAPauthenticationidentity validationdirectory services - Question #534Layer 3 Control Plane
A large enterprise network has two data centers and a WLAN edge with a large hub-and spoke network. The complete network is configured as a single OSPF area, and spoke routers are...
OSPFtotally stubby areahub-and-spokeLSA reduction - Question #535Layer 3 Control Plane
A customer has a DMVPN network with EIGRP as the overlay protocol. EIGRP timers cannot be shortened, yet the customer requires the detection of lost connectivity between neighbors...
BFDDMVPNEIGRPfailure detection - Question #536Layer 3 Control Plane
When designing a network .Which method can be used to control the exit point for traffic an autonomous system, at the layer 3 control plane?
BGPAS exit pointIGP metrictraffic engineering - Question #537Designing Network Services
Why is a redundant PIM stub router topology a bad network design decision?
PIM stubmulticasttraffic duplicationredundancy - Question #538Layer 2 Control Plane
A switched network is being designed to support a manufacturing factory. Due to cost constraints, fiber-based connectivity is not an option. Which design allows for a stable networ...
UDLDunidirectional linksphysical interferencefactory network - Question #539Layer 3 Control Plane
Refer to the exhibit. Company XYZ has 150 branch locations across the U.S. Each branch is connected to two aggregation routers, one router in each data center. The network is confi...
OSPF NSSAABRLSA propagationroute summarization - Question #540Layer 3 Control Plane
Refer to the exhibit. You must review this single OSPF area, DMVPN network because the company has noticed a few area 0 convergence and stability issues. Also, traffic destined to...
OSPFDMVPNcost metricsconvergence - Question #541Design Considerations
You are designing a new multisite data center network within the same city. You are using the newest routers that run OSPF and DWDM point-to-point interfaces for site-to-site conne...
DWDMLoS/AISinterface failure detectionoptical networking - Question #542Design Considerations
Which two options are design considerations when introducing FCoE into an existing network? (Choose two)
FCoEQoS markingsconverged network adaptersdata center design - Question #543Layer 3 Control Plane
A service provider is designing a new backbone based on an IGP and MPLS what are two valid reasons for implementing MPLS-TE as well? (Choose two)
MPLS-TEtraffic engineeringQoS service classesbackup paths - Question #544Layer 3 Control Plane
Company ABC grew organically and now their single-area OSPF network has an unacceptably slow convergence time after a topology change. To address the slow convergence time, they wa...
OSPF multiareaaddress summarizationABRsuboptimal routing - Question #545Layer 3 Control Plane
Refer to the exhibit. Transit traffic in this large enterprise campus network passes the eBGP core. Per security policy, traffic coming from AS 65444 destined for AS 65466 and vice...
BGP next-hop-selfeBGPbroadcast networktraffic policy - Question #546Layer 3 Control Plane
Refer to the exhibit. Which routing solution is the most scalable to connect the branches to the HQ and to connect the branches together over the internet using DMVPN?
DMVPNEIGRP stubbranch routingscalability - Question #547Layer 3 Control Plane
Which OSPF design consideration, with regards to simplicity and address preservation, must be considered when connecting two Layer 3 switches directly using 10 GBASE-T cabling and...
OSPF network typepoint-to-pointaddress conservationadjacency - Question #548Designing Security
Your customer recently acquired a company with a national WAN of 750 locations consisting of MPLS VPN-based sales, Internet-based sites and sites with direct links to regional hub...
DMVPNIPsecWAN encryptionhierarchical hub-and-spoke - Question #549Layer 3 Control Plane
A network is designed to use OSPF to reach eBGP peers. For eBGP peers to stay stable in case of a link failure, what condition should be avoided?
BGP stabilityOSPFeBGP peeringlink failure - Question #550Layer 3 Control Plane
Which two options are Loop-Free Alternate design considerations? (Choose two)
Loop-Free Alternatefast reroutebackup pathSLA - Question #551Designing Management and Operations
Which three processes are part of the ITILv3 Service Operation? (Choose three)
ITILv3service operationincident managementproblem management - Question #552Layer 3 Control Plane
You must make IGP redesign recommendations for a client that has old equipment, with low CPU power and memory, that they do not have budget replace. They are very concerned about C...
IS-ISmesh groupsfloodingCPU optimization - Question #553Design Considerations
You are hired to assist an enterprise customer to design their global WAN network. A protected DWDM circuit with disjoint fiber routes and guaranteed restoration times is ordered t...
BFDDWDMfailure detectionrestoration time - Question #554Layer 3 Control Plane
An enterprise customer A with provider-independent address space is dual-homed to two ISP. Which two options , when combined, allow for customer A to efficiently achieve out-bond t...
BGP load balancingdual-homeddefault routeoutbound traffic - Question #555Designing Network Services
Across a large WAN network, there will be new video traffic being distributed from a single source at any given time however, the video source might originate from different parts...
Source Specific MulticastPIMmulticast designoptimal path - Question #556Designing Network Infrastructure
Which two options describe the advantages of using DWDM over traditional optical networks? (Choose two)
DWDMoptical networkingchromatic dispersionbandwidth expansion - Question #557Designing Network Services
Refer to the exhibit. As part of a redesign project, you must predict multicast behavior. What is the resultant multicast traffic receiving on the shared tree( , G), if it is recei...
multicast RPFshared treeLHRPIM - Question #558Evolving Technologies
What two options are significant drivers for 5G in IoT networks? (Choose two)
5GIoTlow latencymass connectivity - Question #559Evolving Technologies
Which two options are IoT use cases that require the low-latency and high reliability that 5G networks provide? (Choose two)
5GIoT use casesindustrial automationautomotive - Question #560Designing Security
As a part of a network design, you should tighten security to prevent man-in-the-middle. Which two security options ensure that authorized ARP responses take place according to kno...
Dynamic ARP InspectionDHCP snoopingARP securityman-in-the-middle - Question #561Layer 3 Control Plane
Which two options are benefits of using Topology Independent Loop-Free Alternate in WAN design? (Choose two)
TI-LFAsegment routingLDP backupWAN convergence - Question #562Layer 3 Control Plane
Which two options are potential problems with route aggregation? (Choose two)
route aggregationsuboptimal routingasymmetric routingroute summarization - Question #563Layer 3 Control Plane
In an OSPF network with 20 routers connected together with Ethernet cabling , which topology typically takes the longest to converge?
OSPFnetwork topologyconvergencering topology - Question #564Designing Network Services
A DMVPN network is being deployed for 10 branch sites to connect to the central headquarters over the Internet. Each branch site connects to the internet via a 1.5 Mb/s ADSL line,...
QoSDMVPNhierarchical QoStraffic shaping - Question #566Designing Network Services
Refer to the exhibit. This enterprise customer wants to stream one-way video from their head office to eight branch offices using multicast. Their current service provider provides...
multicastMPLS VPNGRE tunnelL3VPN - Question #567Designing Management and Operations
A customer requests that you determine how much of their remote branch traffic into a central data center is related to a call manager that resides in the data center. Which soluti...
NetFlowtraffic monitoringnetwork managementcall manager - Question #568Network Virtualization
Refer to the exhibit. Each branch network must connect to the HQ and other branch networks over the phase 2 DMVPN network using a single tunnel interface. OSPF is running over the...
DMVPN phase 2OSPF network typenext-hop preservationspoke-to-spoke - Question #569Network Virtualization
As network designer, which option is your main concern with regards to virtualizing multiple network zones into a single hardware device?
network virtualizationfate sharinghardware consolidationdesign risk - Question #570Network Virtualization
You are reviewing a new data center design for a customer. They chose to leverage a tunnel- based overlay technology for quick deployment and multitenant security. Which design con...
overlay networkMTUtunnel encapsulationdata center design - Question #571Designing Network Services
Refer to the exhibit. Which solution must be used to send traffic from the foreign wireless LAN controller to the anchor wireless LAN controller?
wireless LAN controllerEoIP tunnelanchor controllerWLAN mobility - Question #572Designing Security
Which three items do you recommend for control plane hardening of an infrastructure device? (Choose three)
control plane hardeningCoPProuting protocol authenticationSNMPv3 - Question #573Layer 3 Control Plane
Which native mechanism does OSPF use to prevent loops in MPLS VPNs?
OSPFMPLS VPNDN bitloop prevention - Question #574Designing Network Infrastructure
Your client is considering acquiring a new IPv6 address block so that all Ethernet interfaces on the network receive addresses based on their burned-in hardware addresses, with sup...
IPv6 addressingEUI-64VLAN subnettingaddress planning - Question #575Layer 3 Control Plane
An enterprise network has two core routers that connect to 200 distribution routers and uses full- mesh iBGP peering between these routers as its routing method. The distribution r...
iBGProute reflectorBGP scalabilityfull mesh peering - Question #576Designing Management and Operations
A healthcare customer requested that health statistics from their infrastructure devices are to be sent over their service provider MPLS network. Which protocol must be enabled?
SNMPv3network managementsecure monitoringMPLS - Question #577Designing Network Services
Which two application requirements are mandatory for traffic to receive proper treatment when placed in the priority queue? (Choose two)
QoSpriority queueLLQjitter tolerance