JN0-481 Exam Questions

When viewing the devices in the Managed Devices table, you see that some devices are listed in the OOS-READY state. What does this state mean for the device?

What are two agent processes that operate within the Juniper Apstra device agent? (Choose two.)

Which two statements are correct about a Juniper Apstra server? (Choose two.)

In Juniper Apstra, which statement about resources is correct?

What is the purpose of an EVPN Ethernet segment identifier (ESI)?

What are two available Juniper Apstra template types? (Choose two.)

The same connectivity template is applied to the ge-0/0/6 interface on both borderleaf1 and borderleaf2 nodes. This connectivity template describes the intended configuration of th...

Off-box agents are consuming too much CPU and memory on your Juniper Apstra controller. In this scenario, how would you solve this problem?

In Juniper Apstra terminology, to which network operating system concept does a routing zone refer?

You want to route between tenants in a multitenant environment in Juniper Apstra. What are two ways to accomplish this task? (Choose two.)

When creating a probe, an operator wants to make it easy to view that probe's output. In this scenario, which element must be created to accomplish this task?

Which three multihoming mechanisms are supported in the Juniper Apstra rack design? (Choose three.)

You are using Juniper Apstra to manage your three-stage IP fabric. You have not enabled any IBA probes other than those that are enabled by default. You notice that both the Analyt...

You have an EVPN-VXLAN data center IP fabric, with all single-homed hosts/servers. Which two EVPN route types are present in this scenario? (Choose two.)

You are deploying a data center fabric using Juniper Apstra. The fabric contains 100 leafs and four spines. Which statement is correct about IP addressing in this scenario?

You are trying to deploy a five-stage template to a blueprint as shown in the exhibit. You cannot see your template name in the list of available templates. In this scenario, which...

Which Root Cause Identifier is currently supported in Juniper Apstra software?

At which point in the design process does the operator choose IPv4 or IPv6 for a spine-and-leaf link underlay type?

What are three phases of the Juniper Apstra data center life cycle? (Choose three.)

You are creating a new security policy using Juniper Apstra. Referring to the exhibit, which application point should you select to allow or deny traffic to or from a particular VR...

What are three valid resource types supported within Juniper Apstra? (Choose three.)

You have a configuration deviation in the Juniper Apstra dashboard. What does this anomaly indicate in this scenario?

In a three-stage Clos network, what are important key design aspects of a data center fabric? (Choose two.)

You are creating a template using Juniper Apstra. In this scenario, what is a rack-based design compared to a pod-based design?

The servers attached to your Juniper Apstra managed data center fabric are running VMware. You want to get the details about which VMs are attached to which leaf interface. Referri...

Which statement is correct about an event log?

You are asked to deploy a collapsed fabric architecture. Which two statements are correct about this deployment? (Choose two.)

What are three port group roles that you are allowed to assign to a logical device? (Choose three.)

In Juniper Apstra, what are three valid deploy modes when assigning systems to your blueprint? (Choose three.)

Which two protocols can be used to advertise EVPN routes? (Choose two.)

What are two formats that the cabling map can be exported as? (Choose two.)

An operator is working on a capacity-panning exercise. The operator needs to examine the pre- built time series information regarding link utilization. In the Juniper Apstra UI, wh...

Referring to the exhibit, what happens when an operator clicks the Accept Changes button on the right side of the screen in Juniper Apstra?

Which two statements are correct about Juniper Apstra reference designs? (Choose two.)

You have accessed your deployed blueprint and see the banner shown in the exhibit. Which two statements are correct in this scenario? (Choose two.)

What are two types of policies that Juniper Apstra uses to push to switches using Security Policies? (Choose two.)

Which two statements are correct about a Juniper Apstra server? (Choose two.)

You want to assign resources to your blueprint during the deployment phase. In this scenario, which statement is correct?

Which element of an intent-based analytics (IBA) probe is used to specify the database objects to which the probe will apply?

The analytics probe shown in the exhibit is enabled. The ge-0/0/5 interface on the "my-esl-001- leaf1" node receives an average of greater than 1 Mbps of traffic. Which two stateme...

Juniper Apstra provides five different predefined user roles. Given this information, what is the main difference between the administrator and the user role?

You are creating a new template that will connect two rack based templates together. Which rack type should be used to accomplish this rask?

In the Apstra design phase, what is the role of DC Reference Design?

Which of the following two statements are correct?

How does Apstra use Fabric Device Management to ensure consistency across the network?

You have created a blueprint and are in the process of assigning systems. You require the leaf3- sonic device in the blueprint but do not want it to actively participate in the rou...

What does VXLAN use to uniquely label and identify broadcast domains?

You are building a blueprint using Juniper Apstra and must change the cable map to match the physical environment. Where in the blueprint UI is this task accomplished?

You are using Juniper Apstra to create security policies that create ACLs on the fabric devices. What are two valid objects that would be used within Apstra in this scenario? (Choo...

What does clicking the indicated icon shown in the exhibit accomplish?