HPE7-A08 Exam Questions

Refer to the exhibit: How can you implement route summarization for the routes originating from Area 2?

Drag and Drop Question Place the problem-solving methodology steps in the correct order, with the first step starting at the top. Answer:

You are reviewing the configuration of a VSX lag and have noticed the command lacp fallback. Why might this have been configured?

Which statement about managing VSX switches in HPE Aruba Networking Central is true when one of the switches may not be fully configured?

After enabling 802.1X authentication on all switch ports connected to AOS10 access points, users joining SSIDs in bridge mode no longer receive an IP address. Users of tunnel mode...

An eBGP configuration is set up from HPE Aruba networking CX 6300 to two peers. Both peers advertise the 10.200.0.0/23 subnet with the default configuration. What configuration imp...

Drag and Drop Question Match each network requirement to the most appropriate routing protocol. Options may be used more than once. Answer:

You are configuring ClearPass to profile devices using the Data Interface in SPAN mode. What configuration is required on a CX switch?

On an HPE Aruba Networking CX switch, what needs to be done to complete the redistribution of the selected static routes using a single area OSPF when partial configuration already...

For the aggregation layer, you must configure two new HPE Aruba Networking CX 6200M (VSF) switches. LACP link aggregations to downstream access switches using redundant ports from...

Based on the given output from an HPE Aruba Networking CX 6300: Which statement about the output above is true?

Your customer requires encrypting and authenticating Ethernet frames between all APs and CX switches. Which solution should you recommend?

How would the route type affect the configuration if an OSPF configuration has several external routers?

After configuring NTP and the time zone on your switch and configuring a matching time zone in your browser, you notice an error message in the NAE dashboard saying, "Switch time a...

You have recently configured WMM to DSCP mapping on your HPE Aruba Networking APs and want to make sure that only the correct traffic is prioritized on the wired network. What shou...

Drag and Drop Question Match the terminology related to 802.1x authentication. Answer:

How would you explain to a new HPE Aruba Networking CX customer how the switch can protect against use cases of malicious DHCP servers and ARP poisoning in the network where client...

Your company needs to run BGP in a multi-homed configuration to two ISPs, advertising a block of public address space you own. Which AS number would be an example of a suitable num...

Your customer's CISO would like to deploy colorless ports across the network. Which will you need to configure to meet this requirement?

A junior engineer has configured eBGP between two CX switches (Agg-1 and Agg-2) using the configuration below, and tells you that the neighbors are in the 'Active' state. What can...

You need to configure BGP on an HPE Aruba Networking switch using AS 65010. What is required when establishing peering with neighboring devices using eBGP AS 65100?

Refer to the exhibit. A senior network architect has created the configuration above. You are implementing the set up in building A and B. The actual fiber distance between the bui...

You are configuring OSPF between two CX switches but cannot see any neighbors. Based on the output, how would you fix the problem?

After configuring IGMP snooping on a Layer 2 VLAN, multicast applications are no longer working. Which additional configuration step is required?

Drag and Drop Question Match where the configuration for loop-protection is defined on an Aruba CX switch. Options may be used more than once. Answer:

You have configured BFD for OSPF on a CX switch and have noticed the BFD session stays down but the OSPF neighbor state is up. What could explain this behavior?

A customer has asked if their new CX switches will support their legacy management system. Which of these would this include? (Choose two.)

You are reviewing the configuration of a VSX lag and have noticed the command lacp fallback. Why might this have been configured?

TAC has made a configuration change on the CLI of a CX switch using aruba-central support- mode. Which statement about the switch configuration in HPE Aruba Networking Central is t...

Refer to the exhibit: The customer would like to utilize Dynamic Segmentation for wired users in Building B. Which statement is true about the scenario?

Which queuing mechanism should you configure to ensure voice traffic is always forwarded with the highest priority?

You have added a switch with existing configuration to an existing group in HPE Aruba Networking Central but the configuration is not synchronizing. What could cause this?

After reviewing a report from HPE Aruba Networking Central, you notice that a 6200F switch configured in VSF with three other members has reached its available PoE budget. What can...

Refer to the exhibit: A senior network architect has created the configuration above. You are implementing the setup in building A and D. The actual fiber distance between the buil...

You are deploying CX switches in a network with over 100 VLANs. Which version of STP should you configure?

You have run a script to configure a new VLAN on a CX switch, but are receiving a '401 - Unauthorized' HTTP response code. What do you need to do to resolve the issue?

You need to run a packet capture on a CX switch and copy the full output directly to an SCP server. What is the best way to do this?

Refer to the exhibit for an HPE Aruba Networking CX 6300M VSF: A lag is configured using ports 1/1/1 and 2/1/1. If Member ID 1 fails, what would happen to the lag?

The customer requires encrypted data between Layer 3 connected data centers. Which feature in the HPE Aruba Networking CX portfolio would support the requirement?

Your company needs to run BGP in a multi-homed configuration to two ISPs, advertising a block of public address space you own. Which AS number would be an example of a suitable num...

Your company needs to run BGP in a multi-homed configuration to two ISPs, advertising a block of public address space you own. Which AS number would be an example of a suitable num...

An HPE Aruba Networking CX 6000 switch is connected to port 1/1/1 on an aggregation layer CX 8325 VSX configuration. The following state is seen on the aggregation switch: The SVI...

You have successfully configured an 'established' eBGP connection to two ISPs. After additional testing, you discovered that Internet connectivity is not working, and both ISPs rep...

You have added a switch with existing configuration to an existing group in HPE Aruba Networking Central but the configuration is not synchronizing. What could cause this?

You have recently configured OSPF between two switches and verified the output of the below command: After a few days, another engineer changed the configuration, and now the outpu...

You are deploying CX 6300 switches and AP-615 access points at a hospital providing connectivity to critical medical devices. Which feature should you enable on the switch to provi...

Refer to the exhibit. Given the current software running on an HPE Aruba Networking CX 8320 VSX, what is the best way to upgrade the VSX cluster with minimal downtime? (Choose two....

OSPF peering is configured between HPE Aruba Networking CX 6300 switches utilizing bfd. With the given configuration on switch A and switch В in its default settings: (config-if)#...

You have recommended that a customer adopt a modem management approach for their new CX switches. Which of these would this include? (Choose two.)