CTS Exam Questions

Which of the following documents includes details about equipment type, model, location, and expected service frequency?

Assuming 120V as the power source, how many amperes does a 240W device draw?

When doing a site survey for the installation of a large LED video wall, what is MOST important to consider?

The goal of initial AV design meetings is to determine:

An AV system has a dedicated managed switch with an IP address scheme of 192.168.10.0/24, but one component is not talking to the rest of the system. What network property should b...

In order to estimate project task duration, one needs to understand the effort required to complete the expected scope and:

Installing an AV system generates a lot of debris. When is the BEST time to identify if there will be a place to dispose of the debris?

At what time of day is it BEST to conduct a site survey?

Which of the following is a benefit of benchmarking in an AV project?

A client has a laser projector that fails and appears dead after six months' use. The documentation shows that the projector is covered by a return-to-base or back-to-bench warrant...

A technician sets up a 1080p LCD screen and connects a 720p source via an 8 m (26 ft) HDMI cable. Later, the source is switched to 1080p output and the image appears on screen, but...

Preventive maintenance is best described as maintenance that is carried out:

A newly installed AV system is experiencing intermittent loss of video on one display. What is the FIRST step the technician should take?

Which document identifies who is responsible for each part of the system delivery, including schedule and scope?

In a basic AV rack, what is the most effective method to promote proper airflow?

Exhibit: These images provide examples of _____ distortion.

Which of these cables should be used for Ethernet transmission over 1 mile (1.6 km)?

This screen has a 16:9 aspect ratio. How close should the nearest viewer be positioned?

Based on this diagram, how many lighting zones are there?

When selecting a DC power supply that has to run a long distance, what must be considered?

A client requires a front projection system. What drawings should be requested from the client to select the appropriate lens?

Which phase comes first in a project?

Projectors may use different lamp technologies for different reasons. For long life without changing the light source, which technology is preferred?

There is concern about the noise level in an AV rack room. What weight setting on the SPL meter should be used to demonstrate that the noise level doesn't require hearing protectio...

Which system is used to show colors from a video display?

The brightness controls on a display adjusts which level?

According to the Gantt chart pictured, the Project Manager should wait to start Activity C until which predecessor has been reached?

As part of a service agreement offering, wfwt PRIMARY role do preventive maintenance visits (PM/PMV) play?

Which frequencies are amplified by a subwoofer?

When doing a site survey, it is MOST IMPORTANT to consider the client's

As the height of a character increases on a display.

Assuming that the speakers in the picture on the LEFT are 8 Q drivers, what is the impedance of the speaker system on the left?

During a routine service visit, an engineer notices an LED indicator on a projector's front panel blinking regularly. What should be done?

When connecting a condenser microphone, what MUST be included in die system design for it to operate?

When creating an estimate for a request for proposal (RFP), what is the FIRST tiling that should be done?

Network Quality of Service (QoS) is defined as

A saeen is 144 in (3658 mm) wide and the throw ratio is 2.3:1. How far from the screen should the projector be placed?

Which method of control is supported by HDBaseT?

During project delivery and after completion, it is important to ensure correct management of control system code so that

What should be done first if a control system's touch screen is reported as locked, frozen, or otherwise not functioning?

When working with a client to design an AV solution for a new conference center, the client requests a detailed budget for the equipment and installation. What phase is the project...

After presenting a proposal to a client, confirming that all objections are answered and that the final buying decision will be made at an internal meeting, what is the next step?

When discussing a proposed audiovisual project with a new customer, it is important for the salesperson to FIRST

Project documentation states the system must logically Isolate control and media networks. What piece of network equipment should be used?

To help end users remember key points of the training, the training documentation should include

When an audio device can no longer accurately reproduce the audio signal, It is called

Which kind of drawing should a technician refer to in order to determine how to hang a loudspeaker line array?

During the site survey, the client indicates that the space that will become a rear projection room is currently an off-white color. What should be recommended to the client?

During an initial customer visit, it is important to determine whether or not one is

The contrast control sets the