200-301 Exam Questions
1,744 real 200-301 exam questions with expert-verified answers and explanations. Page 12 of 35.
- Question #567IP Connectivity
Refer to the exhibit. Routers R1 and R3 have the default configuration. The router R2 priority is set to 99. Which commands on R3 configure it as the DR in the 10.0 4.0/24 network?
OSPF DR electionOSPF priorityCisco OSPF configuration - Question #568
Refer to the exhibit. A company is configuring a failover plan and must implement the default routes in such a way that a floating static route will assume traffic forwarding when...
Static routingFloating static routesAdministrative distanceRoute redundancy - Question #569Network Access
What is one reason to implement LAG on a Cisco WLC?
LAGCisco WLCLink AggregationLink Redundancy - Question #570Security Fundamentals
Which action implements physical access control as part of the security program of an organization?
Physical SecurityConsole Port SecurityDevice Hardening - Question #571
Refer to the exhibit. An engineer is asked to insert the new VLAN into the existing trunk without modifying anything previously configured. Which command accomplishes this task?
VLAN trunkingCisco IOS commandsSwitch port configurationAllowed VLAN list - Question #572Security Fundamentals
Which field within the access-request packet is encrypted by RADIUS?
RADIUS encryptionAAA protocolsPacket encryption - Question #573
A network administrator is setting up a new IPv6 network using the 64-bit address 2001:0EB8:00C1:2200:0001:0000:0000:0331/64. To simplify the configuration, the administrator has d...
IPv6 addressingIPv6 compressionIPv6 notation - Question #574
A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must...
Cisco SSHSSH configurationRSA key generationip domain-name command - Question #575Security Fundamentals
Refer to the exhibit. Which two commands must be added to update the configuration of router R1 so that it accepts only encrypted connections? (Choose two)
Cisco SSH configurationVTY line configurationRSA key generationSecure remote access - Question #576IP Connectivity
A network engineer must configure two new subnets using the address block 10.70.128.0/19 to meet these requirements: - The first subnet must support 24 hosts - The second subnet mu...
VLSMIP subnettingIP address allocationRouter interface IP - Question #577
What is a function of Opportunistic Wireless Encryption in an environment?
Opportunistic Wireless EncryptionWireless securityOpen Wi-Fi networks - Question #578
Refer to the exhibit. Which two commands when used together create port channel 10? (Choose two.)
EtherChannel configurationLACP negotiationPAgP negotiation - Question #579IP Connectivity
Refer to the exhibit. A static route must be configured on R14 to forward traffic for the 172.21.34.0/25 network that resides on R86. Which command must be used to fulfill the requ...
Cisco Static RoutingIP Route CommandSubnetting - Question #581Network Access
Refer to the exhibit. Host A sent a data frame destined for host D. What does the switch do when it receives the frame from host A?
Switch forwardingMAC address tableUnicast flooding - Question #582
What is the function of the controller in a software-defined network?
SDN controllerSDN architecture - Question #583Network Access
Refer to the exhibit. An engineer built a new L2 LACP EtherChannel between SW1 and SW2 and executed these show commands to verify the work. Which additional task allows the two swi...
LACPEtherChannelPort Channel ConfigurationLACP Modes - Question #584
What is a requirement for nonoverlapping Wi-Fi channels?
Wi-Fi channelsWireless networking - Question #585
A network engineer is Installing an IPv6-only capable device. The client has requested that the device IP address be reachable only from the internal network. Which type of IPv6 ad...
IPv6 addressingUnique Local AddressIPv6 address typesnetwork reachability - Question #586IP Services
Refer to the exhibit. Which plan must be Implemented to ensure optimal QoS marking practices on this network?
QoS markingQoS trust boundariesCoS/DSCPAccess layer QoS - Question #587Network Access
Refer to the exhibit. Traffic that is flowing over interface TenGigabitEthernet0/0 experiences slow transfer speeds. What is the reason for the issue?
Ethernet duplexinterface troubleshootingslow network performance - Question #588Network Access
Refer to the exhibit. Site A was recently connected to site B over a new single-mode fiber path. Users at site A report Intermittent connectivity Issues with applications hosted at...
Fiber opticsTransceiversPhysical layer troubleshootingSingle-mode fiber - Question #589Network Access
Refer to the exhibit. Switch A is newly configured. All VLANs are present in the VLAN database. The IP phone and PC A on Gi0/1 must be configured for the appropriate VLANs to estab...
Switchport modesVLAN configurationAccess ports - Question #590
An engineer must configure R1 for a new user account. The account must meet these requirements: - It must be configured in the local database. - The username is engineer. - It must...
Cisco Local UsersIOS Password SecurityScrypt Hashing - Question #591IP Connectivity
Refer to the exhibit. Router R1 resides in OSPF Area 0. After updating the R1 configuration to influence the paths that it will use to direct traffic, an engineer verified that eac...
OSPFRoute selectionECMPCisco path selection - Question #592
What is a requirement when configuring or removing LAG on a WLC?
WLC LAGController ConfigurationReboot Requirement - Question #593Network Access
Refer to the exhibit. The DHCP server and clients are connected to the same switch. What is the next step to complete the DHCP configuration to allow clients on VLAN 1 to receive a...
DHCP SnoopingSwitch securityDHCP configuration - Question #594
What provides centralized control of authentication and roaming in an enterprise network?
Wireless LAN ControllerWLAN management - Question #595IP Connectivity
Refer to the exhibit. Traffic sourced from the loopback0 Interface is trying to connect via ssh to the host at 10.0.1.15. What is the next hop to the destination address?
IP routingRouting table lookupNext hop determination - Question #596
Refer to the exhibit. All interfaces are configured with duplex auto and ip ospf network broadcast. Which configuration allows routers R14 and R86 to form an OSPFv2 adjacency and a...
- Question #597IP Connectivity
Refer to the exhibit. Which network prefix was learned via EIGRP?
EIGRP routingRouting tableNetwork prefixes - Question #598IP Services
Refer to the exhibit. How should the configuration be updated to allow PC1 and PC2 access to the Internet?
Cisco NATNAT interface configurationPAT configuration - Question #599IP Connectivity
Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging...
Static RoutingHost RouteCisco IOSCommand Syntax - Question #600IP Connectivity
Refer to the exhibit. Which command must be issued to enable a floating static default route on router A?
Floating static routeDefault routeCisco IOS routingAdministrative distance - Question #601
Which protocol is used for secure remote CLI access?
SSHRemote accessCLI managementNetwork security protocols - Question #602LAN Switching Technologies – Configure, verify, and troubleshoot VLANs and voice VLAN configurations on Cisco switches (CCNA Routing & Switching / CCST Networking)
Refer to the exhibit. All VLANs are present in the VLAN database. Which command sequence must be applied to complete the configuration? A. B. C. D.
Voice VLANSwitch Port ConfigurationVLANsIP Telephony - Question #603Security Fundamentals
Refer to the exhibit. Which minimum configuration items are needed to enable Secure Shell version 2 access to R15?
Cisco SSHv2Router configurationHostname commandSSH prerequisites - Question #604
What is the purpose of the ip address dhcp command?
Cisco interface configDHCP clientIP address assignment - Question #605IP Connectivity
Refer to the exhibit. Router R1 currently is configured to use R3 as the primary route to the Internet, and the route uses the default administrative distance settings. A network e...
Static routingAdministrative distanceDefault route - Question #606IP Services
Refer to the exhibit. Which configuration enables DHCP addressing for hosts connected to interface FastEthernet0/1 on router R4?
Cisco IOS interface configurationRouter DHCP serverFastEthernet interface - Question #608IP Connectivity / Addressing and Subnetting - selecting appropriate subnet masks to accommodate host requirements with growth planning (CCNA/CCNP Routing and Switching)
Refer to the exhibit. An IP subnet must be configured on each router that provides enough addresses for the number of assigned hosts and anticipates no more than 10% growth for now...
IP SubnettingVLSMIPv4 AddressingNetwork Design - Question #609
Which wireless security protocol relies on Perfect Forward Secrecy?
Wireless SecurityWPA3Perfect Forward Secrecy - Question #610Network Fundamentals
What is a function of an endpoint on a network?
Network endpointsEndpoint functionsNetwork components - Question #611IP Connectivity
Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is use...
IP RoutingRouting Table LookupPacket ForwardingLongest Prefix Match - Question #612Network Access
Refer to the exhibit. An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that t...
VLAN configurationSwitch port modesMAC address tableEthernet switching - Question #613CompTIA Network+ / CCNA - Network Automation and Programmability; Understanding SDN vs. Traditional vs. API-Based Networking architectures
Drag and Drop Question Drag and drop the statements about networking from the left onto the corresponding networking types on the right. Answer:
SDNNetwork TypesTraditional NetworkingAPI-Enabled Networking - Question #614Network Access – Compare and contrast wireless architectures and AP modes (CCNA 200-301 Domain 2)
Drag and Drop Question Drag and drop the facts about wireless architectures from the left onto the types of access point on the right. Not all options are used. Answer:
Wireless ArchitectureAccess Point TypesAutonomous APCloud-Based AP - Question #616Network Fundamentals / Automation and Programmability - Understanding the differences between traditional networking and Intent-Based Networking (IBN), including management paradigms and security models, as tested in Cisco CCNA (200-301) or similar enterprise networking certifications.
Drag and Drop Question Drag and drop the characteristics of networking from the left onto the networking types on the right. Answer:
Intent-Based NetworkingNetwork AutomationTraditional vs Modern NetworkingSecurity Models - Question #617LAN Switching Technologies - Understanding Rapid Spanning Tree Protocol (Rapid PVST+) port states and their associated forwarding behaviors, typically mapped to CCNA/CCNP Switching exam objectives.
Drag and Drop Question Drag and drop the Rapid PVST+ forwarding state actions from the left to the right. Not all actions are used. Answer:
Rapid PVST+Spanning Tree ProtocolSTP Port StatesLayer 2 Switching - Question #618Network Fundamentals - Understanding the differences between TCP and UDP transport layer protocols, their characteristics, and appropriate use cases (maps to CompTIA Network+, CCNA, or similar networking certification objectives)
Drag and Drop Question Drag and drop the TCP or UDP details from the left onto their corresponding protocols on the right. Answer:
TCP vs UDPTransport Layer ProtocolsNetwork FundamentalsConnection-Oriented vs Connectionless - Question #619Security Fundamentals - Explain the elements of network security including AAA services and their role in controlling and auditing network access (Cisco CCNA / CompTIA Security+)
Drag and Drop Question Drag and drop the descriptions of AAA services from the left onto the corresponding services on the right. Answer:
AAAAuthentication Authorization AccountingNetwork SecurityRADIUS TACACS+