JN0-370 Exam Questions

After initial setup on a QFabric system, you investigate a Node device interface that is Juniper JN0-370 Exam operationally down. What are two reasons for this happening? (Choose t...

You have recently configured a BGP peering session. The session uses a Layer 3 connection from a Node device within a server Node group to a BGP router. The BGP peering session doe...

You notice that Fibre Channel over Ethernet (FCoE) traffic is dropped in a QFabric system. What are two reasons why this is happening? (Choose two.)

Which process is responsible for fabric link discovery in a QFabric system?

Which two components in a QFabric system are used to connect to servers within the data center? (Choose two.)

Which service in a QFabric system provides the Junos CLI?

What is the function of a Node device in a QFabric system?

Which Node device design ensures a one-to-one subscription ratio?

Which two statements are true about the Fabric Shortest Path First protocol? (Choose two.)

You want to change the device mode of a QFX3500 to connect to a QFabric system. Juniper JN0-370 Exam Which command would you use?

Which three lengths of 10-Gigabit Ethernet passive direct attach copper (DAC) cables are used by the QFX3500? (Choose three.)

What is the function of a Director device in a QFabric system?

An administrator of a QFabric system needs to know if LLDP is sent out to a neighbor. Which command should you use from a Node device?

You have been asked to merge a newly deployed QFabric system with an existing Layer 2 network. The existing Layer 2 network is running RSTP and must retain ownership of the root br...

What is the number of Node devices supported in a network Node group?

A QFabric system continuously drops Layer 3 inter-VLAN routed traffic. Host 1 is connected to SNG-1 on VLAN 10 and Host 2 is connected to SNG-2 on VLAN 20. You determine that SNG-1...

You are configuring a Node group name. Which statement is correct?

You are asked to log in to an individual QFabric system component and must perform operational commands. Which two login classes would allow you do this? (Choose two.) Juniper JN0-...

You have just deployed a QFabric system and noticed that some of the attached Node and Interconnect devices are not registered in the system's inventory. What are two reasons for t...

The Node device LC0 is receiving packets destined to the host on the Node device LC1. The source IP address of the packets is 20.0.0.1 and the destination IP address is 77.0.0.1. H...

A customer says that a Node device in a Node group that had been working was suddenly disconnected from the QFabric system. Which two commands should you use to troubleshoot the pr...

You are cabling the data plane of a QFabric system using QFX3008-I Interconnect devices. You require an uplink capacity of 320 Gbps from each Node device. Which two statements are...

A customer mentions that a new Node device connected to a QFabric system is not discovered. What are three reasons for this issue? (Choose three.)

A customer needs to plan a QFabric system to support one hundred 10 GbE ports and twenty- eight 8 Gb Fibre Channel ports for a data center consolidation project. The infrastructure...

You want to connect a blade chassis with a blade switch to a QFabric system. Which blade chassis Layer 2 connection requires STP to be enabled?

For which type of Node group does the Routing Engine function reside on a Director device?

Which QFabric system Routing Engine (RE) handles RPD functions?

A customer wants to set up a QFX3000-M QFabric system, which includes Director devices, Interconnect devices, Node devices, and EX4200 switches. The network engineer wants to know...

Host A is connected to two Node devices in a redundant server Node group over a LAG link. Host B is connected to a Node device on a server Node group. Traffic is running between Ho...

What is a Fibre Channel N_Port?

You are configuring the link aggregation groups (LAG) in a QFabric system. Which two statements are true? (Choose two.)

Which two features do Fibre Channel over Ethernet VLANs support? (Choose two.)

You must determine which FTE interfaces of a Node device named Node-1 are connected to which Interconnect device. Which operational mode command provides the desired information?

A new Node device joins a QFabric system. Which statement is correct?

Juniper JN0-370 Exam How many traffic priorities are available in a QFabric system using enhanced transmission selection (ETS)?

A customer is experiencing high packet loss and suspects a Layer 2 loop in the network of a QFabric system and other switches using RSTP. Which two actions will identify the Layer...

Which routing table is used to exchange Layer 3 routes between components in a QFabric system?

You are troubleshooting latency on a Node device on your QFabric system and discover a Layer 2 loop. What would cause this behavior?

Which command executed from NW-NG-0 displays the PFE ID for all nodes in the fabric?

By default, which two TCP/IP ports does iSCSI use for data traffic? (Choose two.)

A customer wants to set up a QFX3000-M QFabric system to consolidate existing 1 GbE networks and to provide a low latency and high performance 10 GbE network. Network engineers mus...

A user account has the remote-debug-permission parameter set but the user is unable to log in to any devices. What is causing this problem?

What is the default behavior for Node groups on a QFabric system?

During the ARP learning operation, which Routing Engine (RE) updates all the nodes of a newly learned ARP entry?

Which three Qfabric system functions run within the Director group software? (Choose three.)

You have just configured a QFabric system as a transit FCoE switch between a server and an FCoE gateway device. The server's converged network adapter state is showing as "Dead". W...

QFabric systems use the bridge-vpn protocol family to perform which function?

Which routing table is used to store Layer 2 routing information on system components? Juniper JN0-370 Exam

What is the function of a control plane switch in a QFabric system?

According to Juniper Networks recommendations, specific ports have been reserved on the EX4200 switches to connect to each of the QFX3000-M QFabric system device types. Which ports...