JN0-370 Exam Questions

Which two values displayed in the output from the show spanning-tree MSTP configuration command must match on all switches participating in the same MSTP region? (Choose two)

Which role does the router ID (RID) have in the BGP route selection process?

Click the Exhibit button. Referring to the network illustrated in the exhibit, how does router A reach destinations in area 49.2222?

You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy. You have been asked to create a static route that will use 43 18 7 1 as its pr...

You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further reduce down time if a Routing Engine (RE) failure occurs. Which two features can be co...

Click the Exhibit button. You work for the regional Internet service provider shown in the exhibit You have a partial BGP table and are receiving a 10 100/16 route from your upstre...

Which BGP state denotes a fully operational session?

Click the Exhibit button. In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1- minute intervals Which router will be the designated router?

You have been asked to configure an IPv6 address for a group of interfaces that could belong on different routers. If a packet is sent to that address, it should be received by all...

What is the function of the hop limit field in the IPv6 header?

Click the Exhibit button. In the exhibit, how many full OSPF adjacencies will R3 have?

You have been asked to define a default gateway for traffic leaving a router. This route should use interface so-0/0/0 as its next-hop. Which type of route would be suited for this...

You are asked to design a Layer 2 switched topology that can automatically recover from link failures. Which type of protocol would you consider in your design?

Click the Exhibit button. When the Junos configuration shown in the exhibit is applied to the router, which routes in the forwarding table will begin load-balancing packet flows?

You have configured MPLS and RSVP in your network using all of the Junos defaults. You established an LSP in your network which is reporting an up status but no traffic is using it...

Using industry best practices, what is true regarding an external BGP session?

You own a home network connecting through an always-on connection and need to assign IPv6 addresses to your routers because you want to follow the guidelines spelled out in RFC 317...

Which two BGP attributes are modified by default when they are passed between external BGP peers? (Choose two)

Click the Exhibit button. In an RSTP network, the root and designated ports have been elected as shown in the exhibit What will be the port type of port 1? Juniper JN0-370 Exam

Which three statements are correct about the QFabric system control plane? (Choose three.)

The QFabric system data plane performs which three functions? (Choose three.)

You are determining the DC power requirements for a QFX3000-M QFabric system. Which two devices support DC power? (Choose two.)

You configured a BGP peering session between your QFabric system and an attached device, but the session is not coming up. What are two reasons for this happening? (Choose two.)

You have recently connected an aggregated interface between a server Node group and a blade chassis switch and the interface is down. Which three reasons would explain the interfac...

Which Routing Engine (RE) in a QFabric system acts as a BGP route reflector for internal reachability?

A customer wants to change the management IP addresses for the fabric administrator and Director devices after the initial setup is completed. Which command should the customer ent...

You are asked to configure a link aggregation group (LAG) between a QFabric system and an attached MX Series router. This LAG must support Layer 3 communications and must be associ...

A customer added a new Node device under an existing Node group, but the new Node device is not discovered by the fabric manager. Which two CLI commands should help with troublesho...

Host A is connected to Node1 on VLAN10. Host B is connected to Node2 on VLAN20. VLAN interfaces for both VLANs are configured on a QFabric system. Host A wants to connect to Host B...

What does a Type-Length Value (TLV) for iSCSI provide in a QFabric system? (Choose two.)

You want to maximize performance and ensure low latency for critical server applications using a QFabric system. What would be used as the first hop gateway for the applications?

You are asked to set up a Director group. What information do you require? (Choose three.)

You are asked to attach a QFabric system to an existing Fibre Channel SAN. Which switch would enable you to accomplish this?

Whenever you connect a Layer 2 switch to the xe-0/0/0 interface of the LC2 Node device in the server Node group of a QFabric system, the interface xe-0/0/0 on LC2 is disabled. What...

What must happen for QFabric system RVIs to become active?

What are two internal protocols in a QFabric system? (Choose two.)

Which Routing Engine (RE) in a QFabric system is responsible for compiling and distributing topology details to system components?

You are powering on a QFabric system. What is the correct power-on sequence? Juniper JN0-370 Exam

On which QFabric system Node group type can a cross-member Layer 3 LAG be configured?

You have enabled OSPF on your QFabric system. Which component will process the incoming hello packets?

When bringing up a QFX3000-M QFabric system control plane network, which three actions should be performed? (Choose three.)

Which IP range does the fabric manager Routing Engine use for internal control plane device communication on the QFabric system?

After changing the Node group designation for a Node device, you notice that the Node device is disconnected. What is causing the problem?

You need to determine the status of the Director devices from the fabric administrator. Which command would you use?

What are two architectural goals of QFabric systems? (Choose two.)

You are performing a nonstop software upgrade on a QFX3000-M QFabric system. According to Juniper Networks recommendations, which two upgrade processes are recommended? (Choose two...

A customer says that no 10 GbE interfaces in a Node device are operational. What are two reasons for this happening? (Choose two.)

You are asked to investigate FCoE traffic congestion issues on a QFabric system. Which two CLI commands would you use? (Choose two.)

Which three Qfabric system hardware architectures help ensure high availability and minimize downtime? (Choose three.)

A QFabric system is configured with only RSTP. A connected switch is configured with VSTP with all the ports in the trunk port allowing all VLANs. Which two behaviors are expected?...