HP0-Y37 Exam Questions
85 real HP0-Y37 exam questions with expert-verified answers and explanations. Page 1 of 2.
- Question #1
Which protocols are supported on the HP A-Series switch? (Select three.)
- Question #2
You want to enable RRPP on interface Gigabit Ethernet 1/0/4 of an HP A-Series switch. Which commands should be configured on this interface? (Select two.)
- Question #3
Given the following Router 2 Configuration: ``` <Router-2> bgp 65001 network 16.1.0.0 255.255.0.0 network 16.2.0.0 255.255.0.0 network 16.3.0.0 255.255.0.0 undo synchronization pee...
- Question #4
Click the Exhibit button and view the four exhibits. You are replacing your Cisco distribution layer switches with HP E8212 zl switches. The Cisco switches have a VLAN map applied...
- Question #5
Click the Exhibit button and view both exhibits. In the exhibits, you see the QoS-related configurations for two Cisco switches, one at the edge and one at the distribution layer....
- Question #6
Drag and Drop Questions Click the Task button. A customer wants to replace the two Cisco switches at the distribution layer (Cisco_D1 and Cisco_D2) with two HP A-Series switches. C...
- Question #7
RRPP statues for an HP A-Series switch indicate that Hellos are being received on the secondary port but do not indicate that Hellos are being sent on the primary port. What most l...
- Question #8
Click the Exhibit button. You are beginning the process of replacing Cisco switches at the distribution layer of your network with HP A-Series switches. Management has requested th...
- Question #9
Click the Exhibit button. You are in the process of replacing Cisco switches at the distribution layer with HP E-Series switches. At this point, you have removed one of the Cisco d...
- Question #10
Click the Exhibit button. You are in the process of replacing Cisco switches at the distribution layer with HP E-Series switches. The migration will be running Multiple Spanning Tr...
- Question #11
Click the Exhibit button. A customer has a Cisco-based network, and you are replacing the distribution layer switches with HP E-Series switches. The customer wants you to perform t...
- Question #12
What happens when the 10 Gigabit Ethernet link 1/0/25 shown in the exhibit is disconnected from the HP A5800 switch IRF Member 5? (Select two.)
- Question #13
A company has a network with Cisco switches that implement PVST+ but wants to migrate to MSTP, which all of its switches support. What is your first step for starting the migration...
- Question #14
You are in the process of replacing Cisco switches at the distribution layer with HP A-Series switches. You have connected the A-Series switches in parallel with the existing Cisco...
- Question #15
The 10 Gigabit Ethernet link 1/0/25 between the HP A5800 switches in the exhibit is disconnected from IRF Member 5 for several minutes. What happens when the cable is reconnected?
- Question #16
The exhibit displays the basic steps in one migration process for replacing Cisco distribution layer switches with HP E-Series switches. For which of these customers would this met...
- Question #17
You are planning to replace Cisco distribution layer switches with HP A-Series switches, and you are selecting a general strategy for the migration process. The strategy you select...
- Question #18
After you issue the command irf-port configuration active on HP A5800 Switch members 4 and 5, the 10 Gigabit Ethernet link 1/0/25 is connected. What is the expected result?
- Question #19
Click the Exhibit button. You have been asked to troubleshoot a problem in a multi-area OSPF network. Users connected to R3 are not able to access any destinations outside of Area...
- Question #20
Click the Exhibit button. Click the Exhibit button and view the three exhibits. Which combination of BGP attributes will be chosen as the best path for prefix 18.0.0.0/8?
- Question #21
Traffic from AS 65001 destined for network 192.137.0.0/16 leaves AS 65001 via the Serial 3 interface of Router 1. The administrator prefers that this traffic leave AS 65001 via int...
- Question #22
A company's LAN is composed of Cisco switches only. The network runs Rapid PVST+ with the short pathcost method. Cisco distribution switches are set as root and secondary root in a...
- Question #23
Network 16.2.0.0/16 is advertised by Router 1 and Router 2 into BGP. All traffic from AS-65002 destined to 16.2.0.0/16 enters AS 65001 via the Serial 3 interface of Router 1. The a...
- Question #24
Which configuration is valid for Switch 5?
- Question #25
Click the Exhibit button. Which combination of BGP attributes will be chosen as the best path for prefix 22.0.0.8?
- Question #26
Click the Exhibit button and view both exhibits. Which configuration is valid for Switch 4?
- Question #27
A company's network includes Cisco switches that are running PVST+. The distribution switches are configured as root and secondary root for all existing VLANs. There are 80 switche...
- Question #28
The 10 Gigabit Ethernet link 1/0/25 shown in the exhibit is disconnected from HP A5800 switch IRF member 8 for several minutes. What happens several minutes after the cable is reco...
- Question #29
Click the Exhibit button and view a network diagram and a switch configuration. What are possible node modes of Switch 6 in RRPP ring 3? (Select two.)
- Question #30
During the past several weeks, users have begun complaining about the poor quality of VoIP phone calls. While VoIP has been in use for several months, recently there has been netwo...
- Question #31
What is a characteristic of load balancing in RRPP?
- Question #32
You are migrating a customer's distribution layer from Cisco Catalyst 3560 switches to HP A7500 Series switches. You are not planning the Layer 3 migration. The Cisco switches use...
- Question #33
A company's Cisco network runs VTP. VTP is set in Server mode on distribution switches and in Client mode on edge switches. To prepare for the insertion of HP switches at the edge...
- Question #34
Two BGP routers, the "local" and "the remote," are connected to a switch. An EBGP session is established between them. What will happen if an Ethernet interface is disconnected on...
- Question #35
A company's Cisco network is configured with PVST+, and the distribution switches are the root and secondary roots in the existing VLANs. You want to migrate the company's network...
- Question #36
Which statements about BPDU Guard are correct? (Select three.)
- Question #37
Click the Exhibit button and view a network diagram and a switch configuration. In RRPP ring # 3, which type of port is interface G 1/0/2 of Switch 2?
- Question #38
Click the Exhibit button.
- Question #39
BGP Configuration in HP Comware OS bgp 100 network 200.1.0.0 255.255.254.0 peer 222.222.10.1 as-number 200 peer 222.222.10.1 route-policy IN-CORP1 import peer 222.222.10.1 bfd quit...
- Question #40
Click the Exhibit button. BGP Configuration in HP Comware OS bgp 100 network 200.1.0.0 23 peer 222.222.10.1 ip-prefix out-filter export ip route-static 200.1.0.0 23 null0 ip ip-pre...
- Question #41
Click the Exhibit button. <Router-1>display bgp routing-table Total Number of Routes: 24 BGP Local router ID is 172.21.0.1 Status codes: * - valid, > - preferred, h - history, i -...
- Question #42
Click the Exhibit button. Customer A Customer A Site-1 Site-2 Customer A Site-3 Customer B Customer B Site-1 Site-2 Customer B Site-3 A provider of MPLS services configures MPLS La...
- Question #43
You are replacing your Cisco distribution layer switches with HP A-Series switches. The Cisco switches have a VLAN map applied to VLAN 21 (subnet 10.2.21.0/24). The current Cisco c...
- Question #44
Refer to the exhibits showing the IRF configurations of HP A5800 switches (Members 2, 3, 4, 5) and the network diagram on page 4. After you issue the command `irf-port-configuratio...
- Question #45
You are planning to replace Cisco distribution layer switches with HP A-Series switches, and you are selecting a general strategy for the migration process. The strategy you select...
- Question #46
Click the Exhibit button. <Switch-7>display rppp verbose domain 2 Domain ID : 2 Control VLAN : Major 3000 Sub 3001 Protected VLAN: Reference Instance 0 to 16 Hello Timer : 1 sec Fa...
- Question #47
Click the Exhibit button and view a network diagram and a switch configuration. What happens when the 10 Gigabit Ethernet link 1/0/25 shown in the exhibit is disconnected from the...
- Question #48
This Cisco-based network is configured with PVST+.The Cisco network of an Example Corp.shown in exhibit is configured with PVST+. What will happen if you change Spanning Tree mode...
- Question #49
Click the Exhibit button. The administrator's terminal is connected to the console port of IRF Member 4 of the IRF stack of 4 shown in the exhibit. The administrator saves the conf...
- Question #50
On a company's Cisco network, VLANs are learned through VTP. On the edge switches, allowed VLANs on VLAN trunks are restricted to VLANs that contain end nodes. This reduces the num...