D-PEMX-DY-23 Exam Questions

When a SAS IOM is power cycled, how much time does it take for the storage-IOM to display mapping information?

Which is the minimum iDRAC license required to use the Platform Restore feature of the Lifecycle Controller?

An administrator needs to start collecting detailed data points on the PowerEdge MX7000 power usage. What is the minimum requirement?

A server administrator wants to configure chassis power, thermal, and fans metric reports on a PowerEdge MX7000 chassis. Which type of license is required?

Refer to the exhibit. A customer recently replaced all the dual-port network cards in mezzanine A with quad-port network cards across all 16 PowerEdge MX740c sleds in the two-chass...

What component enables the MX840c compute sled to have this configuration? 4 x CPUs 4 x mezzanine cards 2 x mini mezzanine cards 48 DDR4 DIMM slot

A server sled has a single mezzanine card installed in the correctly supported slot. To which IOM fabric(s) does the sled have access?

A company receives their first MX7000 chassis. They connect all the provided power supply cables into two different PDUs on different power grids for redundancy. Each of the six po...

A system administrator must interface the compute sleds of an MX7000 chassis to a Z9432F-ON in a single SmartFabric. Which FEM IOM is required?

When performing "A1 the Box" management, what must be done to successfully connect to the Management Module?

A system administrator is designing a solution for a customer who will be purchasing a large number of PowerEdge MX7000 chassis. For ease of management, they would like to have the...

On which generation of server was the BOSS-N1 controller introduced?

Which statement describes L2 Multicast as implemented on the PowerEdge MX7000 IOM?

In the External Fabric Manager OME-M, what programming interface is used to manage the fabric?

What automatically opens a support case with technical support and collects the PowerEdge MX system state information that is required for troubleshooting an issue, then sends it s...

A system administrator must carry out a SupportAssist log collection on an MX750c sled using iDRAC that includes operating system logs. What is required?

An administrator is configuring a fully populated MX5016s storage sled to be accessed by four MX740c compute sleds. Each compute sled has an H745P Jumbo PERC installed. The disks i...

What is the maximum supported drive configuration on a PowerEdge MX840c compute sled?

Which component on the PowerEdge MX7000 uses a hot-plug serviceability model?

What is the benefit of C22 power inlet connectors on the MX7000 chassis?

A system administrator must obtain the correct rail and cable management to install a newly purchased MX7000 chassis into a rack. What type of rail and cable management is supporte...

Which MX7000 feature allows an administrator to virtualize network WWN and MAC addresses?

What are the required components for a PowerEdge MX7000 Minimum to POST configuration?

While servicing an MX7000 chassis a system administrator logs into OME-M and receives a Chassis Mismatch error. What should be the next step taken by the administrator?

Once power is applied to the chassis, what is the next sequence after MM completes booting?

To which component can a firmware update be applied without affecting any applications running on the server?

Which SmartFabric Services Engine component is responsible for managing requested changes for the specific switching node?

Where is a valid storage location for extracting the full MX7000 chassis logs package?

What type of power cord connects to the PSU side of a PowerEdge MX7000?

In an MX7000, which components are cooled by the rear fans?

In addition to one compute sled, one management module, and one IOM, what is the minimum required HW configuration on the PowerEdge MX7000 to POST?

Which uplink configuration combination of the Top of the Rack Switch and the MX7000 Management Module is supported?

Which section of the PowerEdge MX7000 chassis provides a structure for mounting PSUs and sleds?

In the assigned mapping of the MX5016s storage sled what is an assignment option used for independent storage to be mapped to a compute sled?

A technician replaces a failed Management Module in an MX7000 chassis group. After the technician leaves the site, the administrator reports that the lead chassis is no longer able...

The MDB chassis tub assembly vertical distribution board provides connectivity to which chassis components?

Refer to the exhibit. What is shown?

An administrator has installed the iDRAC Service Module in the OS on a compute sled, they are unable to use its features in the iDRAC web GUI. What is the likely cause of this issu...

A server administrator is deploying a VMware vSphere cluster and configuring High Availability on a PowerEdge MX7000 modular system. Which configuration is required?

Where in the OME-M Web interface can the Chassis Deployment Wizard be found?

What can be used as the firmware update source for OME-M within an MX chassis?

Which MX7000 component is responsible for Fabric Consistency Check?

What types of network shares are supported for hosting the firmware catalog for a PowerEdge MX7000 chassis?

What are the typical ambient inlet temperature readings that ATMOS hardware and fans support?

What is a valid option when resetting iDRAC to factory defaults?

Which ports will be active in an MX9116n FSE if there are dual-port NICs in all the server sleds?

What type of connection is used by QuickSync 2?

A network administrator must implement a 100 GbE network in their MX7000 chassis group. Which two components satisfy this requirement? (Select 2)

Why is the backup lead configuration important in an MCM Group?

Which I/O module is supported for Fabric B?