D-PEMX-DY-23 Exam Questions

What configuration is supported for a fully populated MX740c compute sled?

Which protocol(s) does Redfish use?

A systems administrator must extract log files from an MX7000. The logs cannot be saved locally and must only be stored on a secure file server. Which share protocols can they use...

A customer is implementing a clustered three-chassis solution. Which two components are required? (Select 2)

What is the number of server-facing ports and the bandwidth of each port on the MXG610s? (Choose two.)

What does OBPAR allow on a PowerEdge MX750c?

An implementation engineer prepares to install a PowerEdge MX7000. Which serial cable do they use?

What feature does OME-M v1.3 provide when replacing the Right Control Panel?

A server administrator wants to configure RAID on drives that are assigned to a compute sled. Which interface can be used to complete the task?

What are the correct CLI commands to configure the management IP Address on either the MX9116n or the MX5108n switches running SmartFabric OS10?

A system administrator must assign six of the MX5016s drives to a single MX750c compute node. Which assignment mode accomplishes this task?

What are the components of the control panel of a PowerEdge MX750c sled?

Which feature in OpenManage Mobile can be used to allow the monitoring of a PowerEdge MX7000 chassis?

An administrator is receiving notifications about insufficient power for a PowerEdge MX7000 chassis. The chassis is fed from two different power grids. What is the best policy to m...

Which micro controller-based module allows the Management Module to communicate with all the hardware present in a PowerEdge MX7000 chassis?

An administrator is asked to install and power-on a new MX740c sled in an MX7000 chassis. The administrator inserts the sled and presses the power button. They notice that the powe...

Which controller option the mapping of an entire MX5016s to multiple compute sleds?

An administrator is mapping the drives of an MX5016s. The disk must be split in groups among multiple compute sled slots. Which storage configuration must be used?

A customer has an MCM group consisting of four MX7000 chassis. They need to take the lead chassis down to perform maintenance. How can the customer ensure that another chassis take...

How are double-width compute sleds on the MX7000 numbered from the front?

A technician is doing an initial MX7000 setup and wants to use KVM to configure the MM. KVM is not working. What are the two causes of this issue? (Select 2)

What is a benefit of SmartFabric Services Mode?

What is the port configuration of the MX9116n FSE?

An administrator is asked to install and power on a new MX740c sled in a PowerEdge MX7000 chassis. The administrator inserts the sled and presses the power button. The power button...

An administrator is connecting two MX840c to an MX5016s. The MX5016s is configured in Enclosure Assigned mode. What should the requirements of this mode be to avoid configuration i...

The iSM is available under which license(s)?

An administrator is about to perform a firmware update on an MX9116n switch OS 10 from the CLI. The latest OS 10 switch firmware image has been downloaded and their TFTP server is...

Which three components are required in an MX7000 chassis to allow multiple compute sleds to share access to the same disks in an MX5016s enclosure? (Select 3)

The MX9116n FSE has two single-density QSFP28 port groups, and the default setting for these two ports is 1x 100GbE. What other Ethernet breakout configurations are supported?

Which two-socket PowerEdge sled can support up to eight E3.s NVMe Gen 5 SSD drives?

Which is an invalid option for the PowerEdge MX7000 control panel?

What is a characteristic of MX7000 networking in Scalable Fabric Mode?

Which VLAN is reserved for internal switch communication?

A data center team is working on a solution to monitor and manage data center devices from anywhere. Which feature can be configured to perform these tasks?

When multiple MX9002m modules are daisy-chained to Top-of-Rack switches, which uplink port can be used for stacking?