300-370 Practice Questions
171 real 300-370 exam questions with expert-verified answers and explanations. Page 2 of 4.
- Question #53
A WLAN engineer has just completed a wireless network installation using Cisco 2700 series access points. After checking the WLC, it seems that the APs are running in medium power....
- Question #54
Refer to the exhibit. Which statement describes how the Band Select feature works on the wireless controller?
- Question #55
An engineer must open a support case with Cisco TAC. Which two commands verify the model and serial number of a controller? (Choose two)
- Question #56
A network engineer has identified clients who are experiencing delays white roaming. The network is configured with WPA2-Enterpnse. AES encryption, 802 1X authentication, and Cisco...
- Question #57
A recently acquired Cisco Aironet 1550 series AP is unable to join the WLC. This message is observed on the AP console: AAA Authentication Failure for UserName: CC93.1981.0035 User...
- Question #58
An engineer is using various techniques to discover and isolate rogues on the network. For which technique must the engineer consider legal ramifications?
- Question #59
Refer to the exhibit. The AP is unable to join the controller. What is the cause of this error?
- Question #60
Refer to the exhibit. A VoWLAN has been deployed at a customer site. and users report that audio is choppy in some areas The exhibit captures a voice exchange between one phone tha...
- Question #61
A network engineer is having wireless multicast fail when it hits the wired network. What command will show the source of multicast groups for troubleshooting?
- Question #62
A customer wants FSR and certificate-based authentication. The solution must be simple to deploy. Which method should be used to meet the requirements?
- Question #63
A network engineer is upgrading the WLC image through the GUI for maintenance. What three transfer methods are available? (Choose three.)
- Question #64
During Layer 2 intercontroller roaming, which two items change? (Choose two.)
- Question #65
Which set of commands assigns a standalone access point an IP address of 10.0.0.24 with a 27- bit subnet mask and a gateway of 10.0.0.1?
- Question #66
Which AP to Wireless LAN Controller discovery process requires a previous association of the AP with a Cisco WLC?
- Question #67
Which three options are limitations when configuring basic security on an autonomous AP when using the express security page setup? (Choose three.)
- Question #68
Which two statements about beacon frames used by access points are true? (Choose two.)
- Question #69
When a guest client is authenticated, which type of connection is created between the controller- based AP and the client?
- Question #70
When the enterprise-based authentication method is used for WPA2, a bidirectional handshake exchange occurs between the client and the authenticator. Which five options are results...
- Question #71
After receiving an alert regarding a rogue AP, a network engineer logs into Cisco Prime and looks at the floor map where the AP that detected the rogue is located. The map is synch...
- Question #72
Which configuration step is necessary to enable Visitor Connect on an SSID?
- Question #73
Which two statements describe the software v7.0 implementation of LAG on a Cisco controller? (Choose two.)
- Question #74
A wireless engineer wants to deploy high availability on a wireless network, on what you should be concerned about?
- Question #75
An engineer is configuring a BYOD provisioning WLAN, which 2 are requested?
- Question #76
A wireless engineer wants to configure local flexconnect authentication over CLI, what commands are necessary (Choose 3)?
- Question #77
Which three options are valid client profile probes in Cisco WLC? (Choose three)
- Question #78
Which two statements describe WGB access to a Cisco Unified Wireless Network that is running code 7.0.116.0? (Choose two.)
- Question #79
Which two EAP types are tunneled? (Choose two.)
- Question #80
You have designed your wireless network for data coverage. However, as 5 GHz device a client's increase over legacy 2.4 GHz devices, you observe roaming issues and instability of w...
- Question #81
An engineer uses the shutdown and no shutdown commands on a switch port that an access point is connected to because the AP had disassociated. These commands usually resolve the is...
- Question #82
What is the recommended maximum height of the antenna?
- Question #83
From where to do MSE password recovery?
- Question #84
When use autonomus migration template on WCS, what will be needed on the autonomous AP?
- Question #85
When use fingerprinting method, which is the least cost , easiest lateration to use? the options were :TDOA , cell of origin , VOR , )
- Question #86
Why we have 20% bonus for active mesh parent?
- Question #87
When audit and config group enforcement failed, what alarm severity will be?
- Question #88
What is the antenna type used for location services?
- Question #89
What needs to be the same for seamless roaming?
- Question #90
WAN limitations for Hreap?
- Question #91
After issuing show rfid summary, tag wasn't there, what two commands to check why?
- Question #92
What is this command used for :config mesh astools?
- Question #93
Maximum number of virtual domains in WCS?
- Question #94
The license needed for MSE client tracking based on RSSI and tags?
- Question #95
If aps on two WLCs in one mobility domain lose their controller, by default how will orphaned APs attach to WLCs? WLC with least number of APs registered? WLC with lowest percentag...
- Question #96
In a new deployment, your team has connected many access points in a single switch and you noticed that some access points are not getting power. Which command on a Cisco switch ca...
- Question #97
AAA server has issues with client authentication, how to fix?
- Question #98
What encryption used for mesh link?
- Question #99
The num of rogue APs is consuming the MSE license of context aware elements, how to fix that without removing location of rogues?
- Question #100
How to check nmsp status for switch?
- Question #101
What are the operations have most effect on MSE and WCS cpu?
- Question #102
In dense environment there is interference for location deployment, how to fix?