200-301 Exam Questions

An engineer must configure a WLAN using the strongest encryption type for WPA2-PSK. Which cipher fulfills the configuration requirement?

When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?

Refer to the exhibit. Which VLAN ID is associated with the default VLAN in the given environment?

Which two VLAN IDs indicate a default VLAN? (Choose two.)

Refer to the exhibit. Which statement about the interface that generated the output is true?

Which command should you enter to view the error log in an EIGRP for IPv6 environment?

If a notice-level messaging is sent to a syslog server, which event has occurred?

What are two southbound APIs? (Choose two )

Which feature on the Cisco Wireless LAN Controller when enabled restricts management access from specific networks?

Which command automatically generates an IPv6 address from a specified IPv6 prefix and MAC address of an interface?

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.)

Refer to the exhibit. Which two statements about the network environment of router R1 must be true? (Choose two.)

Which two statements about exterior routing protocols are true? (Choose two.)

Which two pieces of information about a Cisco device can Cisco Discovery Protocol communicate? (Choose two.)

Which two statements about NTP operations are true? (Choose two.)

Which command is used to specify the delay time in seconds for LLDP to initialize on any interface?

A Cisco IP phone receive untagged data traffic from an attached PC. Which action is taken by the phone?

Refer to the exhibit. Based on the LACP neighbor status, in which mode is the SW1 port channel configured?

Refer to the exhibit. The show ip ospf interface command has been executed on R1 How is OSPF configured?

R1 has learned route 192.168.12.0/24 via IS-IS, OSPF, RIP and Internal EIGRP Under normal operating conditions, which routing protocol is installed in the routing table?

Which IPv6 address block sends packets to a group address rather than a single address?

Which feature or protocol is required for an IP SLA to measure UDP jitter?

Which two pieces of information can you learn by viewing the routing table? (Choose two)

Refer to the exhibit. Which two events occur on the interface,if packets from an unknown Source address arrive after the interface learns the maximum number of secure MAC address?...

Refer to the exhibit. Which feature is enabled by this configuration?

For what two purposes does the Ethernet protocol use physical addresses?

Refer to Exhibit. An engineer is configuring the NEW York router to reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as the primary path. Which two commands mu...

Refer to Exhibit. How does SW2 interact with other switches in this VTP domain?

Drag and Drop Question Drag and drop the networking parameters from the left on to the correct values on the right. Answer:

Drag and Drop Question A network engineer is configuring an OSPFv2 neighbor adjacency. Drag and drop the parameters from the left onto their required categories on the right. No al...

Drag and Drop Question Refer to the exhibit. Drag and drop the networking parameters from the left on to the correct values on the right. Answer:

Which NAT term is defined as a group of addresses available for NAT use?

After you deploy a new WLAN controller on your network, which two additional tasks should you consider? (Choose two)

Which component of an Ethernet frame is used to notify a host that traffic is coming?

Refer to the exhibit. How will switch SW2 handle traffic from VLAN 10 on SW1?

You are configuring your edge routers interface with a public IP address for Internet connectivity. The router needs to obtain the IP address from the service provider dynamically....

What are two reasons that cause late collisions to increment on an Ethernet interface? (Choose two)

Which IPv6 address type provides communication between subnets and cannot route on the Internet?

A user configured OSPF in a single area between two routers A serial interface connecting R1 and R2 is running encapsulation PPP. By default which OSPF network type is seen on this...

You have two paths for the 10.10.10.0 network - one that has a feasible distance of 3072 and the other of 6144. What do you need to do to load balance your EIGRP routes?

Drag and Drop Question Drag each route source from the left to the numbers on the right. Beginning with the lowest and ending with the highest administrative distance. Answer:

Which two commands can you use to configure an actively negotiate EtherChannel? (Choose two)

Refer to the exhibit. Which two statements about the interface that generated the output are true? (Choose two)

Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency? (Choose two.)

Which two statements about the purpose of the OSI model are accurate? (Choose two)

Which option best describes an API?

Which of the following is the JSON encoding of a dictionary or hash?

What will happen if you configure the logging trap debug command on a router?

How does STP prevent forwarding loops at OSI Layer 2?

Which three statements about MAC addresses are correct? (Choose three)