200-301 Exam Questions

What is the primary different between AAA authentication and authorization?

When a floating static route is configured, which action ensures that the backup route is used when the primary route fails?

Which two outcomes are predictable behaviors for HSRP? (Choose two)

Refer to the exhibit. Which password must an engineer use to enter the enable mode?

How do TCP and UDP differ in the way that they establish a connection between two endpoints?

When a site-to-site VPN is used, which protocol is responsible for the transport of user data?

What is the primary effect of the spanning-tree port fast command?

How will Link Aggregation be implemented on a Cisco Wireless LAN Controller?

Refer to the exhibit. Which route does R1 select for traffic that is destined to 192 168.16.2?

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)

Refer to the exhibit. Which command provides this output?

Which set of action satisfy the requirement for multi-factor authentication?

Which mode allows access points to be managed by Cisco Wireless LAN Controllers?

Router A learns the same route from two different neighbors, one of the neighbor routers is an OSPF neighbor and the other is an EIGRP neighbor. What is the administrative distance...

Refer to the exhibit. What is the effect of this configuration?

Refer to the exhibit. Which prefix does Router1 use for traffic to Host A?

What are two characteristics of a controller-based network? (Choose two)

Refer to exhibit. Which statement explains the configuration error message that is received?

Drag and Drop Question Drag and drop the application protocols from the left onto the transport protocols that is uses on the right. Answer:

Which command must you enter to guarantee that an HSRP router with higher priority becomes the HSRP primary router after it is reloaded?

Which command should you enter to verify the priority of a router in an HSRP group?

Which command should you enter to configure a device as an NTP sever?

Which two pieces of information can you determine from the output of the show ntp status command? (Choose two)

Which effete does the aaa new-model configuration command have?

Refer to the exhibit. Which command would you use to configure a static route on Router1 to network 192.168.202.0/24 with a nondefault administrative distance?

What is the destination MAC address of a broadcast frame?

Which command is used to enable LLDP globally on a Cisco IOS ISR?

Which of the following dynamic routing protocols are Distance Vector routing protocols?

You have configured a router with an OSPF router ID, but its IP address still reflects the physical interface. Which action can you take to correct the problem in the least disrupt...

Drag and Drop Question Drag and drop the benefits of a cisco wireless Lan controller from the left onto the correct examples on the right. Answer:

Which command should you enter to configure an LLDP delay time of 5 seconds?

Which keyword in a NAT configuration enables the use of one outside IP address for multiple inside hosts?

Which unified access point mode continues to serve wireless clients after losing connectivity to the Cisco Wireless LAN Controller?

Which QoS Profile is selected in the GUI when configuring a voice over WLAN deployment?

Refer to the exhibit. With which metric was the route to host 172.16.0.202 learned?

When OSPF learns multiple paths to a network, how does it select a route?

Refer to the Exhibit. After the switch configuration the ping test fails between PC A and PC B Based on the output for switch 1. Which error must be corrected?

Which command enables a router to become a DHCP client?

Which two encoding methods are supported by REST APIs? (Choose two)

Refer to the exhibit. What is the effect of this configuration?

In a CDP environment, what happens when the CDP interface on an adjacent device is configured without an IP address?

Refer to the exhibit. When PC 1 sends a packet to PC2,the packet has. Which source and destination IP address when it arrives at interface Gi0/0 on router R2?

Which feature or protocol determines whether the QOS on the network is sufficient to support IP services?

An email user has been lured into clicking a link in an email sent by their company's security organization. The webpage that opens reports that it was safe but the link could have...

What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?

Refer to the exhibit. An engineer configured NAT translations and has verified that the configuration is correct. Which IP address is the source IP after the NAT has taken place?

Refer to the exhibit. The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 i...

A user configured OSPF and advertised the Gigabit Ethernet interface in OSPF By default, which type of OSPF network does this interface belong to?

An engineer is asked to protect unused ports that are configured in the default VLAN on a switch. Which two steps will fulfill the request? (Choose two)

Which output displays a JSON data representation? A. B. C. D.