NACE-CIP2-001 Exam Questions

The standards defining surface cleanliness achieved by centrifugal blast cleaning are:

You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has...

You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3rd party NACE Level 3 inspe...

Surface preparation of concrete is performed using:

NACE No.13/ SSPC 6 identifies the use of:

Differences in technique for abrasive blasting concrete versus steel require the operator to:

The Concrete Repair Institute's comparators can be used to assess:

Surface preparation methods for Non-ferrous metals are:

A single component water borne acrylic coating cures by:

When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:

External coatings applied to buried pipelines are generally tested for:

You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified. This is not a...

Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:

When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:

The most likely area of failure on a buried external pipeline coating is the:

The best choice of instrument for holiday testing of thick film concrete coatings is:

Thermal Spray coatings provide:

The primary purpose of Fireproofing coatings are to provide:

When using a destructive Paint Inspection Gauge the NACE inspector must:

Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.

When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:

Coating application to concrete substrates is:

Application of Thermal Spray Coatings requires:

You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method....

Galvanizing performs best in which of the following exposures:

Ideally, documentation requirements should be defined:

Inspection and Test Plans are provided to:

Inspection and Test plans are developed by referencing:

When completing the Final Inspection report the Inspector should write the report using:

Non-Conformance Reports are designed to:

You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next...

Inspector reports should always be copied to:

As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.

As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:

You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors. Your FIRST preferred course of action is to:

When ASIN D 3363 is specified the Inspector must:

When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:

When performing inspection in accordance with ASTM D 4138 the Inspector will use:

NACE International Standards are developed by:

The main reason dehumidification is used during coating operations is to

All of these are advantages of using repair patches EXCEPT

Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?

Linings are used on the interior of pipelines to

Which is used to calibrate a pH meter?

Dehumidification is defined as the removal of moisture vapor from the air to

In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?

A reinforced coating is

Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires

Corrosion is the reverse process of

Coating surveys may include which steps? Select All That Apply: