HP0-Y49 Exam Questions
74 real HP0-Y49 exam questions with expert-verified answers and explanations. Page 1 of 2.
- Question #1
Which wireless technology is limited to operate in a frequency range with only three non- overlapping channels?
- Question #2
Refer to the exhibit. Exhibit Comware switch output. A network administrator has implemented link aggregation on an HP Comware switch using LACP. Assume the two ports are functioni...
- Question #3
Refer to the exhibit. Exhibit Switch configuration. A network administrator is configuring an aggregated link between an HP Comware and ProVision switch. The network administrator...
- Question #4
Which technology does the HP Virtual Connect support?
- Question #5
When LLDP is enabled, which value is presented by default as the LLDP Chassis ID on both ProVision and Comware switches?
- Question #6
What is the default payload size for an 802.3 Ethernet frame on HP switches?
- Question #7
Two OSPF routers are on a segment, and both of their interfaces become active. What is the initial OSPF state after an adjacency has formed?
- Question #8
A network administrator executes these commands on an HP Comware switch: [Comware] super password level 1 simple hp1 [Comware] super password level 2 simple hp2 [Comware] super pas...
- Question #9
Which statement is true about BPDU-Protection on HP Comware switches?
- Question #10
Which STP protection feature does HP recommended against rogue switches?
- Question #11
The HP Virtual Connect (VC) product is found within which HP FlexNetwork Architecture component?
- Question #12
A network administrator has a network of HP ProVision switches with operator and manager passwords configured. The network administrator uses the copy config startup-config tftp <I...
- Question #13
Which Layer 2 mechanism should be used to authenticate wireless or wired users before allowing them access to network resources?
- Question #14
Refer to the exhibit. The server shown in the exhibit is configured for dynamic LACP. There is only one link between Switch 1 and Switch 2. Which HP switching solution should the n...
- Question #15
When configuring MSTP, how should VLANs be separated to perform load balancing?
- Question #16
What is an advantage of connecting servers directly to the HP FlexFabric?
- Question #17
A customer is implementing an access layer solution with four HP Comware switches in an IRF topology. The customer expects to add two additional switches of the same model. What mu...
- Question #18
Which methods can a network administrator use to upgrade the operating system of an HP ProVision switch? (Select two)
- Question #19
In software-defined (SDN), what connects the Application layer to the physical device or Infrastructure layer?
- Question #20
What is the maximum number of Watts that the IEEE 802.1af standard supports?
- Question #21
What is a valid parameter that a network administrator can use when creating a Comware static route?
- Question #22
What does an IP host learn from an ARP reply?
- Question #24
Which HP device or port type can modify, read, and respond to 802.1Q VLAN tags?
- Question #25
A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches?
- Question #26
A network administrator has created and applied a configuration to an HP Provision switch. The network administrator then copied the active configuration to a TFTP server. Upon exa...
- Question #27
What are the correct factory default settings when the HP Comware and Provision switches are originally booted?
- Question #28
Refer to the exhibit. A network administrator is upgrading the operating system on an HP Comware switch. When copying the new image from a TFTP server to flash of the switch, the p...
- Question #29
Which command can a network administrator execute to manage configuration files on an HP Comware switch?
- Question #30
A network administrator has just completed the initial configuration of an HP Comware switch. The network administrator saved the configuration to flash but wants to ensure that is...
- Question #31
Which term refers to aggregated links on HP ProVision switches?
- Question #32
Refer to the exhibit. The network consists of two IP ProVision Switches with routing disabled. How should the network administrator configure the link between Switch A and Switch B...
- Question #33
A company has purchased Intelligent Management Center (IMC) and wants to centralize AAA policies for the HP switches on the IMC server. Which protocol should the company use for th...
- Question #34
Which HP Intelligent Management Center (IMC) component would a network administrator check to verify the installation of IMC or an add-on module?
- Question #35
A network administrator has purchased the first HP Comware for a company. The network administrator has never used the CLI of a Comware device before and needs to perform specific...
- Question #36
Refer to the exhibit. What does the term "blackhole" mean for the 10.11.30.0/24 route?
- Question #37
Which parameter is enabled by default on an HP Commware switch, but disabled by default on an HP ProVision switch?
- Question #38
A routing protocol has three characteristics: - Has fast convergence with triggered,incremental updates via link stateadvertisements(LSAs) - Is classlessprotocol allowing for ahier...
- Question #39
Refer to the exhibit. Exhibit: partial output of the HP Comware display ip routing command. Note the Pre or Preference column. On an HP ProVision switch, what is the corresponding...
- Question #40
Which HP ProVision switch command could a network administrator use to upgrade the operating system from an attached USB drive?
- Question #41
A network administrator attempts to create a loopback interface on an HP Comware switch, and it fails. These are the commands the network administrator issues to do this. [Comware]...
- Question #42
A network administrator configures this command on an HP ProVision Switch: Vlan 30 ip helper-address 10.0.3.253 After the network administrator configures the command, using in VLA...
- Question #43
Refer to the exhibit. Exhibit: Network diagram and routing tables Why does traffic from PC1 fail to reach PC2?
- Question #44
Refer to the Exhibit. Exhibit: HP Comware switch configuration. [Comware] vlan 100 [Comware-vlan100] quit [Comware] vlan 200 [Comware-vlan200] quit [Comware] interface g1/0/22 [Com...
- Question #45
Which HP solution delivers automated virtual machine orchestrator, automatic synchronization of network connectivity information, and visibility to performance of wired and wireles...
- Question #46
Which 802.1X component seeks authentication?
- Question #47
Which management protocol is enabled, by default, on HP Provision switches?
- Question #48
Which HP Comware command saves the startup configuration file to a TFTP server?
- Question #49
Which open standard allows a switch with PoE support to correctly determine the power requirements of a connected device?
- Question #50
Which statement is true about wireless technologies?
- Question #51
Refer to the exhibit. Exhibit HP Comware command output. Examine this output from the Comware command shown in the exhibit. Based on the flag of ACDEF, what is the status of the ag...