D-NWG-FN-23 Exam Questions
277 real D-NWG-FN-23 exam questions with expert-verified answers and explanations. Page 5 of 6.
- Question #201
When using Policy Based Routing what is a valid matching criterion?
- Question #202
Refer to the exhibit. The output shown is from which command?
- Question #203
What are the correct steps to configure a static LAG on a Dell Networking OS10 switch?
- Question #204
What is the size of the VLAN tag in an Ethernet frame?
- Question #205
When the show ip bgp neighbors command is issued, which BGP state reflects a successfully created adjacency with another BGP peer?
- Question #206
What is the default lease time in hours for an address lease in DHCP?
- Question #207
What is the valid range of VLAN IDs for Dell EMC Networking OS10 switches?
- Question #208
Which LSA type provides information necessary to reach routers originating type 5 LSA's in other areas?
- Question #209
What is the default PIM-SSM IP range?
- Question #210
Refer to the exhibit. Where is the rendezvous point for the group 239.255.255.250?
- Question #211
Which switch mode is used to manage files and display switch information?
- Question #212
Which LSA type contains information about routes redistributed into OSPF?
- Question #213
Which command shows whether a LAG protocol is static or dynamic on a Dell EMC Networking OS10 switch?
- Question #214
Refer to the exhibit. No static routing has been configured. For iBGP loopback-based peering, which statement is correct?
- Question #215
Refer to the exhibit. A default route exists on OS10-C that points all internet traffic towards 10.0.13.3 on OS10-B. A network administrator needs to re-route internet traffic only...
- Question #216
How are multiple hardware based ACLs filtered?
- Question #217
When creating an alias in OS10 what is the maximum number of variable input parameters that can be defined?
- Question #218
Which LSA types are used in a single area OSPF topology?
- Question #219
An administrator is implementing VLT in OS10. What type of port-channel must they configure for the VLTi?
- Question #220
Which configuration supports tagged frames on VLAN 20 and untagged frames on VLAN 5?
- Question #221
What is required to enable ECMP in BGP?
- Question #222
A network administrator enters the BGP command neighbor 10.0.2.1. The BGP router does NOT have any route to the 10.0.2.0 network. What will happen?
- Question #223
In a PIM Sparse Mode (PIM-SM) based multicast topology, what function does the Rendezvous Point provide?
- Question #224
A customer has disabled LLDP on the management interface of the switch. What is the proper command to re- enable it?
- Question #225
When implementing QoS on a 10Gb connection, 6Gb is required by the customer. What QoS level best fits the requirement while keeping resource use to a minimum?
- Question #226
Two OS10 switches reside within a VLT domain with statically configured primary-priorities. The current primary peer, switch OS10-A, has a priority of 100, while the secondary peer...
- Question #227
What version of IGMP is required by PIM-SSM receivers?
- Question #228
What is the maximum number of LLDP neighbors supported per system with OS10?
- Question #229
You have been asked to examine a BGP configuration for a co-worker who is having difficulty establishing BGP peering. The address shown is that of the neighbor's Lo0 interface. Giv...
- Question #230
What is a valid OS10 iBGP configuration?
- Question #231
What is a feature of virtual routing and forwarding (VRF)?
- Question #232
On what does PBR base routing decisions?
- Question #233
How are ACLs processed?
- Question #234
When configuring VRRP in tandem with VLT, what is the default VRRP mode?
- Question #235
A network administrator wants servers to avoid spanning-tree convergence immediately after connecting to a leaf switch. Which spanning-tree feature would allow this?
- Question #236
When installing OS10 on a switch from a USB drive, what format is used for the file system?
- Question #237
What benefit does VRRP version 3 provide over VRRP version 2 in OS10?
- Question #238
Which commands are required to properly configure an OS10 switch to run OSPF on eth1/1/3 and to add network 144.254.1.0/30 to OSPF area 0?
- Question #239
From which range can a network administrator choose when setting the RSTP priority value?
- Question #240
Which router types are contained in a single-area OSPF implementation?
- Question #241
Which field in an IP header is used for QoS marking?
- Question #242
What type of network in a Data Center flattens the core and aggregation layers into a single tier?
- Question #243
At which layer does LLDP operate?
- Question #244
In the OS10 CLI what does Ctrl+A do?
- Question #249
At which layer of the OSI model is the Rapid Spanning Tree protocol used to prevent switching loops?
- Question #250
Which parameter is required to match an OSPF Adjacency to form?
- Question #251
A Dell Networking N3024 has a link aggregation configured as shown: interface Gi1/0/1 channel-group 1 mode active exit ! interface Gi1/0/2 channel-group 1 mode active exit ! interf...
- Question #252
A technician configures RIP on a new N-Series switch to connect to an existing switch that runs RIP. The routing table is not populating even after the network statements are added...
- Question #253
Which of the following is an optional LLDP TLV?
- Question #254
A network administrator needs to identify which MAC addresses are static. Under which column in the output of the show mac-address-table command is this information displayed?