D-NWG-FN-23 Exam Questions

What is the benefit of using VLANs?

Which of the following is the starting prefix to denote a link local address?

What is the decimal equivalent of the binary number 10101010 in IPv4?

Given the following customer environment: - Two switches are connected with two crossover cables - STP is disabled What will happen between the two switches?

Which two subnet masks should be used to achieve a network increment of 4? (Choose two.)

On which OSI layers do standard ACL filters operate?

In which Spanning Tree protocol state does a port record MAC addresses but does not forward the data?

Refer to the output: console#show interfaces switchport gigabitethernet 1/0/5 Port: Gi1/0/5 VLAN Membership Mode: Access Mode Access Mode VLAN: 3 General Mode PVID: 1 (default) Gen...

What are the default credentials for the Dell EMC OpenManage Network Manager?

Which option is used to configure Network Address Translation (NAT) to provide one-to-one mapping between local and global addresses?

Which metric is used by link-state routing protocols to determine the best path?

What is the default route preference value for OSPF?

Which OS10 command shows the image stored in the standby partition?

How many stackable units are supported by a C1048P Rapid Access Node?

What is the dynamically assigned port range in the Transport layer?

A technician creates a new connection between two switches. After configuring the VLANs, the technician looks at the MAC table and sees no MAC addresses learned on the new interfac...

Which of the following is the IPv6 loopback?

What are two commonly deployed PoE powered devices? (Choose two.)

Refer to the output: A network outage occurs. A technician tries to log in to a switch by Telnet using the correct local username and password. What is causing the login failure?

The "show ip ospf database" command outout indicates Type 5 LSAs. What does presence of Type 5 LSA indicate?

Which command should be used if a switch running OS10 must honor incoming pause frames on an interface?

Which type of account would provide access to view the switch configuration without allowing the user to configure the switch?

In IPv4, what is the proper conversion from decimal to binary for the number 226?

A cloud administrator is provisioning several user accounts that have administrator rights to assets using JSON within an IaaS cloud platform. The administrator is required to conf...

What is the correct OS10 command to view LLDP timing information?

Refer to the exhibit. Switch A and Switch B are connected to each other. Both switches use interfaces Gi1/0/1 and Gi1/0/2. Switch A has a Spanning Tree priority of 8192 and Switch...

Which flags are used in the TCP header to initiate and end TCP connections or sessions?

Which traffic type is used to send a packet to an IPv6 address to a specific group of devices?

A technician needs to add an IP for management. When adding an IP, the technician received the following message: Console (config-if-vlan1) #ip address 10.16.24.32/27 Failed to set...

Which command should be used to apply an access list of 198 to an interface?

What is an advantage of using SmartFabric Services?

Which security practice limits the number of VLANs per trunk?

In IPv4, what is the proper conversion from binary to decimal for the number 11010010?

What is a fundamental risk of the Peer-to-Peer network model?

Which IP address is in the Class B range?

A service technician is deploying four Dell EMC Networking N-Series switches in a company's network. The technician has enabled the Spanning Tree protocol on the switches. Which sw...

A network administrator has a stack of four Dell EMC Networking S4800 Series switches. Each stack unit is configured with a different priority. Which switch will be elected as the...

A technician is using Telnet to access an N2024P. Connections are being terminated after 10 minutes of inactivity. Which action should the technician perform to extend the amount o...

A technician applies an IPv4 address to the Out-Of-Band/Management port of a Dell NSeries switch. Which step allows the technician to use the web interface?

A technician inserts an SFP+transceiver into an N3024F 1 Gbps port on the front panel. The transceiver does NOT work. What is the reason for this issue?

Which Dell EMC Networking operating system does an N-Series switch use?

What is the purpose of the control plane in a router?

Which statement is true about the following command? smartfabric l3fabric enable role LEAF vlti ethernet 1/1/4?

What accurately describes stacking of Dell EMC Networking S4800 Series switches?

Which special IPv6 address is used as the loopback?

Refer to the output shown: console (config-if-Tel/0/1) #switchport general allowed vlan add 2-6 console (config-if-Tel/0/1) #show interfaces switchport tengigabitethernet 1/0/1 Por...

Which protocol is used to map an IPv4 address to a MAC address?

Select the correct command syntax for copying files:

A technician connects two N3024 switches with two cables for redundancy on an existing network. Spanning Tree is disabled. What happens between the two switches?

A technician decides to create an ACL. The technician includes all host and/or protocols allowed within the ACL. Why must the technician take this step?