300-360 Exam Questions

Which two tool in the Cisco Prime Infrastructure can you use to identify whether a floor area can support a new VoIP system? (choose two)

A network engineer is designing a high-density wireless network. To optimize client performance and avoid interference. Which configuration must the engineer use?

You must configure IPV6 to drop unwanted or rogue RA packets that come from wireless clients. Which feature do you enable?

A network installation on the site with ID 331372269 has been determined to be potentially hazardous to install. Which regulatory body must be consulted to ensure safety during the...

You must perform a Layer1 survey by using Metageek Chanalyzer on the current operating mode is configured for Cisco CleanAir AP?

A network engineer is conducting a Layer 1 site survey using a spectrum analyzer. Which four RF sources can be detected? (Choose four.)

A customer requesting a site survey requires hidden APs, basic data coverage, and guest access in a multifloor environment. Which industry vertical best describes this customer?

A small medical office would like to have wireless ability. Which survey tool would provide the fastest AP locations without sacrificing quality?

Which three reasons describe the importance of assessing existing wired infrastructure? (Choose three.)

A 802.11n implementation is being discussed. Users are satisfied with the potential 300- 450 Mbps throughput of new 802.11n APs. Which three bandwidth requirements are used to calc...

A customer wants to trade in older 802.11a/b/g access points for new 802.11n access points. What must be considered before deploying new 802.11n access points?

An engineer needs to perform a site calibration using Cisco WCS. Which two types of data collection can be used? (Choose two.)

On which two items will data be collected when an engineer is conducting a passive survey? (Choose two.)

A customer has requested site surveys for data, voice, video, and location services for their location. The customer will be using RFID tags extensively. Which type of site survey...

Which regulation is OSHA responsible for enforcing?

Which hop count is Cisco's maximum recommended for a client in a wireless Mesh network?

The customer requires connectivity between two buildings that are 100 meters apart. Which type of antenna is suitable for this installation?

An engineer is adding APs to an existing VoWLAN to allow for location based services. Which option will the primary change be to the network?

A customer is experiencing slower client data throughput than the data rate setting. Which two wireless characteristics are the primary contributing factors? (Choose two.)

A network has two Cisco WLCs and two Layer 3 gigabit Ethernet switches. The customer requires two gigabit connections from each Cisco WLC to each of the switches that have copper R...

A wireless engineer is utilizing the voice readiness tool in Cisco Prime for a customer that wants to deploy Cisco IP phones. Which dBm range is the network inspected against?

A wireless engineer must improve the roaming performance of the handheld mobile video units. Which feature must be enabled in the controller?

Which option is the minimum RSSI signal for a VoIP WLAN?

You are designing a wireless network to support voice and video applications. The customer is requesting to use the 2.4 Ghz band only because they primarily use 802.11b legacy devi...

Which value does EDRRM AQ threshold Low represent?

What RF phenomenon results from a presence of metallic I-beams, conveyor belts, chain-link fences, and metallic shelves found in a warehousing environment?

A customer requesting a site survey requires hidden APs, basic data coverage, and guest access in multifloor environment. Which industry vertical best describes this customer?

You are designing a wireless network that contains many different types of wireless clients. How do you conduct a survey to ensure a consistent experience for all of the wireless c...

Which option is an enhancement of enabling WMM on an AP?

An engineer is upgrading the legacy access points to 802.11ac Wave 2 capable access points. The existing gigabit uplinked switches provide 802.3at. Which switch limitation is a con...

You are using Ekahau to plan a wireless network. Which unit of measurement is used by RF obstacles to show RF loss?

An engineer is designing the physical infrastructure for an IEEE 802.11ac network. Which power design should the engineer use?

A wireless engineer is calibrating a floor using Cisco Prime Infrastructure. Which setting in the WLC must be disabled before the floor calibration is started?

A wireless engineer is designing a wireless network for a campus. Which two parameters can have a negative effect on the Wi-Fi coverage of an access point? (Choose two.)

When a post-installation audit is performed using the Ekahau Survey tool, which two steps are associated with the passive portion of the audit? (Choose two.)

Which two modifications to station behaviors were designed in the IEEE 802.11e protocol? (Choose two.)

You are designing a network deployment for a state college. The college has six buildings. Each building has a WLC located in the IDF to support access points. Which type of wirele...

You must optimize an IPv6 wireless design to ensure that RA packets from routers can be trimmed to a minimum frequency that still maintains IPv6 client connectivity. Which configur...

A wireless engineer is doing a pre-site survey. Which two attributes must match between the site survey and the production clients? (Choose two.)

A network engineer is retrofitting an existing building wired with Category 5e with AP 3800 and mGig switches. Which cable length allows for 5G operation?

While evaluating a post-installation WLAN deployment, problems are occurring when a client roams from one AP to another. The client bounces back and forth between APs. Which two it...

Which design limitation of dual-band WLAN must be considered when end-user devices stream real- time applications and services utilizing dual-band SSID?

An engineer is performing a predictive RF design of a typical office environment. Which value is the most likely attenuation of a cubical wall for this environment?

What is the minimum RSSI signal for a data WLAN?

What is the Cisco-recommended cell overlap percentage for a typical RToWLAN network design?

An initial meeting has been scheduled for a proposed site survey of a customer headquarters location. Which two types of information would be valuable to collect prior to the forma...

A user is running a new video conferencing application on their laptop and is being disconnected as they move from one access point to another. Which situation will cause these dis...

An engineer is shipping equipment, including a battery, for a wireless survey overseas. To ensure that it is accepted onto the aircraft, the battery must comply with which standard...

When a post-installation audit is performed with an auditing tool such as Ekahau, which three steps are associated with the passive portion of the audit? (Choose three.)

You must optimize the 2.4GHz radio usage during the frequency planning of a high-density environment. Which step do you take to ensure that all of the clients can access the APs?