300-360 Exam Questions

An engineer is surveying a customer site for additional wireless coverage. Which two menus will engineer navigate to in order to determine the maximum number of supported APs? (Cho...

What document must be kept current when a customer is conducting network maintenance?

Which functionality on WLAN controllers and APs is used to periodically reconfigure the 802.11 RF network?

The wireless team must configure a new voice SSID for optimized roaming across multiple WLCs with Cisco 7925 phones. Which two WLC settings accomplish this goal? (Choose two.)

Which option lists the non-overlapping channels in the ETSI domain?

An engineer is installing a wireless network in an industrial area with extreme temperatures and a significant amount of dust. Which enclosure should be used to protect the APs?

In an outdoor mesh environment, which is the purpose of deploying one of the access points relatively higher than the others?

A site survey proposes placement of new APs to replace older APs. Which three options are three potential placements of the new APs? (Choose three.)

A company has requested an indoor wireless survey that supports 5GHz radio, 3x4 MIMO technology, and 3 spatial streams. Which AP is used to perform this survey?

An engineer is configuring an AP for a site survey. How should the transmit power be configured?

An engineer is conducting a failover test with a Mesh deployment by disconnecting the network interface of a RAP. A MAP becomes stranded even though it has an acceptable RSSI value...

What measurement can Iperf be used to verify?

What three pieces of information should be included in an installation report? (Choose three.)

What document must be kept current when a customer is conducting network maintenance?

What is the attenuation of a wireless signal that passes through a cider block wall?

After installation of a new data-only wireless network, an engineer found that RRM has set all of the APs to a power level of 1. Which option describes the reason for this?

Which three post-installation checks should an engineer perform after a new wireless installation? (Choose three.)

An engineer is preparing to conduct a site survey with AirMagnet. The engineer wants to capture all 802.11 traffic (not SSID specific) on the first walkthrough. Which survey mode s...

What are two advantages of conducting an active survey versus a passive survey when verifying RF coverage? (Choose two.)

An engineer is surveying a customer site for additional wireless coverage. What two menus will an engineer navigate to in order to determine the maximum number of supported APs? (C...

An engineer is performing a data collection to validate wireless coverage. At what two locations should a linear point collection be performed? (Choose two.)

An engineer has WLC redundancy included in WLAN design documentation, where the WLCs are loaded to half the license capacity therefore allowing half the WLCs to fail without an AP...

During RF verification, some 5 GHz clients are unable to connect to certain APs, while other 5 GHz clients can connect to all APs. What may prevent some clients from connecting?

What two tools can an engineer use to verify RF data rates and coverage after installation? (Choose two.)

How many location points are needed to validate both 802.11b/g and 802.11a in the Cisco WCS Calibration?

You are designing a WLAN by using the capacity planner in Ekahau Site Survey. What is the maximum Peak Hour Usage setting that you can configure?

An engineer is designing a wireless network to support real-time applications across a building and wants to ensure that clients can successfully roam without voice or video interr...

A wireless network is being designed to support 802.11a/b/g/n clients. Which problem occurs when 802.11b clients are heard by APs?

An engineer is performing a post-installation site survey and is concerned that Coverage Hole Detection is negatively skewing the survey results. Which two events signify that Cove...

Which documents must you use to verify the NEC standards for a Cisco 8510 Wireless Controller?

You are designing a wireless network for a small square office. The office can be covered wirelessly by using a couple access points, but the customer requests that the Wi-Fi netwo...

A wireless engineer is designing a wireless network to support real-time applications over wireless. Which IEEE protocol must the engineer enable on the WLC so that the number of p...

You are using the Cisco Aironet 3800 Series access points connected to Cisco Catalyst 3850 switches and you want to use the multi-Gigabit Ethernet feature. Which cable category is...

A wireless consultant is deploying an outdoor mesh network. Which two factors must be considered? (Choose two.)

Which value is the max channel width of the 802.11n protocol?

Which two settings are dependent upon the regulatory domain in which an access point is installed? (Choose two.)

An engineer must install an outdoor wireless network for an area with a direct line of sight. The outdoor APs are in an open area with a history of harsh weather. Which two paramet...

Which tool do you use to identify microwaves and Bluetooth devices when designing a WLAN?

What is the average IP packet loss needed to support real-time application over a wireless network?

You are using the Voice Readiness tool in the Cisco Prime Infrastructure for a customer who needs to deploy Cisco IP phones. Which dBm range is evaluated by the Voice Readiness too...

When designing a VoWLAN network, what is the recommended cell overlap?

You are designing a WLAN for 50 branch offices that require central management. Which controller architecture do you use?

Which value does EDRRM AQ threshold High represent?

Which two items do you assess before you add to an existing wireless network? (Choose two.)

A customer has Radio Resource Management AND Cisco CleanAir enabled. Which element do you evaluate during a post-deployment site survey that these technologies are unable to adjust...

Which two Layer 2 security protocols are supported by 802.11r under the WLAN configuration? (Choose two.)

A wireless engineer completes a site survey for a company. Which three items are included in the site survey report? (Choose three.)

You are optimizing a wireless network that is configured to support IPv6. Which setting do you use to provide first-hop security for the IPv6 clients that use the WLAN?

An engineer must gather requirements for an upcoming wireless design in a manufacturing facility. Which requirement causes concerns for the customer?

An engineer is gathering design requirements from a customer for an upcoming RF design. Which format is the highest quality that floor plans can be requested in?