200-301 Exam Questions
1,744 real 200-301 exam questions with expert-verified answers and explanations. Page 8 of 35.
- Question #357
Refer to the exhibit. Which route type is configured to reach the internet?
default routeIP routingstatic routing - Question #358Network Fundamentals
How does a switch process a frame received on Fa0/1 with the destination MAC address of 0e38.7363.657b when the table is missing the address?
Layer 2 switchingMAC address tableUnknown unicast flooding - Question #359
Which function does the range of private IPv4 addresses perform?
Private IPv4 addresses - Question #360IP Services
Refer to the exhibit. An access list is created to deny Telnet access from host PC-1 to RTR-1 and allow access from all other hosts A Telnet attempt from PC-2 gives this message:"%...
Cisco ACLsStandard ACLsVTY access controlImplicit Deny - Question #361IP Connectivity
Which protocol does an IPv4 host use to obtain a dynamically assigned IP address?
DHCPIPv4 addressingDynamic IP - Question #362
What is a benefit of VRRP?
VRRPGateway RedundancyDefault Gateway - Question #363Security Fundamentals
Refer to the exhibit. What is the result if Gig1/11 receives an STP BPDU?
BPDU GuardSTP BPDUError-disable stateSwitch port security - Question #364Security Fundamentals
Which type of security program is violated when a group of employees enters a building using the ID badge of only one person?
Physical securityAccess controlTailgating - Question #365Network Fundamentals
Refer to the exhibit. PC1 is trying to ping PC3 for the first time and sends out an ARP to S1 Which action is taken by S1?
ARPLayer 2 switchingBroadcast framesMAC address table operation - Question #366
Which technology can prevent client devices from arbitrarily connecting to the network without state remediation?
802.1XNetwork Access Control - Question #367Network Fundamentals
In which situation is private IPv4 addressing appropriate for a new subnet on the network of an organization?
Private IPv4 addressingIP addressing principlesSubnetting basics - Question #368Security Fundamentals
Refer to the exhibit. A network administrator has been tasked with securing VTY access to a router Which access-list entry accomplishes this task?
VTY securityACL configurationSSH remote access - Question #369
Aside from discarding, which two states does the switch port transition through while using RSTP (802.1w)? (Choose two)
RSTP802.1wSwitch port states - Question #370IP Services
When implementing a router as a DHCP server, which two features must be configured? (Choose two)
DHCP server configurationRouter DHCP servicesDHCP address poolDHCP manual bindings - Question #371
An engineer must configure traffic for a VLAN that is untagged by the switch as it crosses a trunk link. Which command should be used?
Cisco TrunkingNative VLANVLAN configuration - Question #372Network Access
What is a role of wireless controllers in an enterprise network?
Wireless controllersWLC managementAP management - Question #373
What is the maximum bandwidth of a T1 point-to-point connection?
T1WAN circuitsBandwidth - Question #374Network Access
Refer to the exhibit. Which switch becomes the root of the spanning tree for VLAN 110?
Spanning Tree ProtocolSTP root bridge electionVLAN STP - Question #375
Where does a switch maintain DHCP snooping information?
DHCP snoopingBinding databaseLayer 2 security - Question #376
Refer to the exhibit. What is represented by "R1" and "SW1" within the JSON output?
JSONJSON valuesJSON structureData formats - Question #377IP Connectivity
Refer to the exhibit. Which configuration must be applied to the router that configures PAT to translate all addresses in VLAN 200 while allowing devices on VLAN 100 to use their o...
Cisco NATPAT configurationAccess ListsWildcard masks - Question #378
Which CRUD operation corresponds to the HTTP GET method?
HTTP methodsCRUD operations - Question #379IP Connectivity
Refer to the exhibit. Which prefix did router R1 learn from internal EIGRP?
EIGRP routingRouting tableNetwork prefixes - Question #380IP Connectivity
Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. what is the reason for the problem?
OSPF neighborOSPF troubleshootingOSPF timers - Question #381
What does a router do when configured with the default DNS lookup settings, and a URL is entered on the CLI?
Router CLIDNS resolutionDefault router settings - Question #382Network Access
Refer to the exhibit. An administrator must configure interfaces Gi1/1 and Gi1/3 on switch SW11 PC-1 and PC- 2 must be placed in the Data VLAN and Phone-1 must be placed in the Voi...
VLAN configurationSwitch access portsVoice VLANInterface configuration - Question #383IP Services
Which condition must be met before an NMS handles an SNMP trap from an agent?
SNMP trapsMIBNMS - Question #384
What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?
OSPF Router IDOSPF ElectionLoopback InterfacesOSPF Process - Question #385Network Access
Which device controls the forwarding of authentication requests for users when connecting to the network using a lightweight access point?
WLAN controllerLightweight APWireless authentication - Question #386IP Services
A network administrator must enable DHCP services between two sites. What must be configured for the router to pass DHCPDISCOVER messages on to the server?
DHCPDHCP Relay AgentRouter configuration - Question #387Network Access
A network administrator needs to aggregate 4 ports into a single logical link which must negotiate layer 2 connectivity to ports on another switch. What must be configured when usi...
LACPLink AggregationEtherChannel negotiation - Question #388IP Connectivity
Refer to the exhibit. Which path is used by the router for internet traffic?
Default routeIP routingRouting tableInternet forwarding - Question #389Network Access
How does a Cisco Unified Wireless network respond to Wi-Fi channel overlap?
Wireless NetworkingChannel ManagementRadio Resource Management (RRM)Interference Mitigation - Question #390Network Fundamentals
What is the difference regarding reliability and communication type between TCP and UDP?
TCP characteristicsUDP characteristicsProtocol reliabilityConnection-oriented protocols - Question #391CCNA - IP Services: Configure and verify inside source NAT using static and pools (Exam Topic 4.7)
Drag and Drop Question Refer to the exhibit. An engineer is configuring the router to provide static NAT for the webserver. Drag and drop the configuration commands from the left o...
Static NATPort Address TranslationNAT ConfigurationIPv4 Addressing - Question #393Network Fundamentals
Drag and Drop Question Drag and drop the network protocols from the left onto the correct transport services on the right. Answer:
Network ProtocolsTCP/UDPApplication Layer ProtocolsTransport Layer - Question #394
With REST API, which standard HTTP header tells a server which media type is expected by the client?
REST APIHTTP headersAccept headerMedia types - Question #395Infrastructure Management and Monitoring - understanding SNMP manager/agent verification commands used to identify, configure, and troubleshoot SNMP components in a Cisco network environment (aligned with CCNA/CCNP Network Management objectives).
Drag and Drop Question Drag and drop the SNMP manager and agent identifier commands from the left onto the functions on the right Answer:
SNMPNetwork ManagementCisco IOS CommandsNMS Configuration - Question #396Infrastructure Management and Monitoring - specifically SNMP configuration and verification commands on Cisco IOS devices, commonly tested in CCNA/CCNP certification exams under network management topics.
Drag and Drop Question Drag and drop the DHCP snooping terms from the left onto the descriptions on the right. Answer:
SNMPNetwork ManagementCisco IOS CommandsNMS Configuration - Question #397The correct arrangement maps as follows - Trusted ports: associate with the legitimate DHCP server and the trusted designation; Untrusted ports: associate with spurious DHCP server (rogue) and the untrusted designation; and the snooping binding database is the mechanism that records validated DHCP leases. This tests Cisco CCNA/CCNP domain objectives around Infrastructure Security and Layer 2 threat mitigation, specifically DHCP snooping operation and port trust classification.
Drag and Drop Question Drag and drop the characteristics of network architectures from the left onto the type of architecture on the right. Answer:
DHCP SnoopingNetwork SecurityLayer 2 SecuritySwitch Port Trust - Question #398IP Services
What is a DNS lookup operation?
DNS lookupName resolution - Question #399Network Access
Refer to the exhibit. A network engineer must configured communication between PC A and the File Server. To prevent interruption for any other communications, which command must be...
Cisco VLAN trunkingAllowed VLANsSwitchport configuration - Question #400Security Fundamentals
Which implementation provides the strongest encryption combination for the wireless environment?
Wireless securityWPA2AES encryptionEncryption protocols - Question #401
What is a characteristic of a SOHO network?
SOHO networksBroadband internet sharing - Question #402Automation and Programmability
Refer to the exhibit. After running the code in the exhibit, which step reduces the amount of data that the NETCONF server returns to the NETCONF client, to only the interface's co...
NETCONFXML filtersNetwork configuration automationData retrieval optimization - Question #403Network Fundamentals
Which resource is able to be shared among virtual machines deployed on the same physical server?
VirtualizationShared storageVM disk sharing - Question #404Network Fundamentals
Which WAN topology provides a combination of simplicity quality, and availability?
WAN topologiesNetwork designAvailability considerations - Question #405
Which command on a port enters the forwarding state immediately when a PC is connected to it?
STP PortFastSpanning Tree ProtocolCisco IOS commandsEthernet switching - Question #406
What are two functions of an SDN controller? (Choose two)
SDN controllerVTN coordinationNetwork topology management - Question #407Security Fundamentals
What is a network appliance that checks the state of a packet to determine whether the packet is legitimate?
firewallpacket inspectionstateful firewall