NACE-CIP2-001 Exam Questions

Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?

The HATE adhesion tester uses

In which type of concrete are laitance commonly encountered?

Generally for safety considerations, waterjetting hose connections use

The number of air turns in an enclosure can be affected by all of these EXCEPT

Pre-cleaning of work pieces will NOT remove

Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?

Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?

You should bulk store coatings containing isocyanates

Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?

Inspectors perform tests on linings that they may not perform on exterior coatings because

The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of

Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?

Cold-applied tape

Examples of non-ferrous metals include Select All that Apply:

Antifouling coatings are regulated by international treaties.

A failure caused by applying a coating too thinly is known as

You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. A...

You are working as an inspector in a galvanizing plant for the first time. What are some of the hazards you need to be aware of:

You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3rd party NACE Level 3 Inspector, representing the owner, presents you with a copy...

An Inspection and Test Plan is required when:

Coating Surveys are legally required:

Individuals conducting Coating Surveys should:

The cost of qualified Coating Inspection is normally offset by:

You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind...

When conducting inspections the Inspector should follow which standards:

You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value. As thi...

When performing testing in accordance with ASTM D 2583 the inspector may observe:

When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:

NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:

NACE Standards include:

You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upo...

When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:

You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of action is to:

NACE Level 2 Inspectors have been authorized to perform:

You can use magnifiers to examine all of the following EXCEPT

Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be

On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?

The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector. Your FIRST preferred course of...

In the event of a conflict between the Product Data Sheet and the Specification:

From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:

You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated...

When environmental enclosures are being used an inspector needs to be concerned about:

It is always possible to see moisture on a steel substrate:

When observing design defects the NACE Inspector should:

When observing fabrication defects the NACE Inspector should:

WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)

Centrifugal blast cleaning requires: