CWDP-305 Exam Questions

If the amplifier in Question 4 has a noise figure of 10 dB but a gain of 0 dB, what is the total noise figure of the cable, amplifier, and filter in series?

During a validation site survey, you realize that the installers mounted some of the APs above the ceiling. They said that this was a request from the building architect due to aes...

What is the most suitable antenna option to be used when designing a WLAN infrastructure with Aps mounted on a ceiling with a height of more than 20 feet and having all of the clie...

A wireless network with fewer APs at higher power levels to cover a large area is said to be which of the following?

What metric implements the simplest algorithm and lowest accuracy in networks requiring locations?

A bandpass filter has a maximum in-band loss of 1.5 dB, ripple of 0.4 dB, and a return loss of 15 dB. What is the minimum in-band loss?

The installation crew for your WLAN project wants to install a few APs to locations nearby the ones specified in the RF design document. What next step should occur? A. Confirm the...

Looking at a client radio specification sheet that states Receive Sensitivity of -82 dBm @ 18 Mbps would mean:

What term refers to the security practice of obfuscating actual data from unintended receivers as the data crosses the transmission medium?

When troubleshooting coverage issues for a wireless network as it appears to new client associations, you should perform which type of survey?

In a convention center, you have received complaints about the WLAN infrastructure. At this moment, the are only two APs in one auditorium. After analyzing the situation, you deter...

What are some advantages of designing guest access with all guest users tunneled directly into the DMZ?

What are three potential benefits when an organization lets their employees bring their own device onto the company s network"?

If a 24-port switch has a PoE budget of 740 W, how many IEEE 802.3at devices can certainly be powered on by it?

When designing a new WLAN infrastructure you also need to be aware of now the network is physically deployed and now the network is logically configured. What are two documents tha...

Which one of the following options would you consider a well-designed WLAN infrastructure when measuring RSSI Notse floor and SNR in a required area?

You have been asked to design a WLAN for an organization. They will be replacing an existing WLAN Currently each AP operates 8 SSlDs on each radio. What will you communicate with t...

What is an advantage of centralized data forwarding?

If you choose to recommend dynamic channel assignment for the APs in your WLAN design what action should you also recommend'?

An AP vendor being considered for a WLAN deployment suggests that their 2 4 GHz and 5 GHz dual-band APs use software defined radios. What unique capability does this indicate in co...

Even when a full pre-design site survey is not performed, what is always recommended to be performed within the deployment areas?

Given A project parameter defines a requirement or constraint (or a project that can be defined before any file imports or design actions. What is an example of a project parameter...

In most WLAN design tools, after defining project parameters or during the project creation wizard what action will you take before you can begin the actual design process?

What is the purpose of defining wall materials in WLAN design software?

To ensure that your design meets the requirements of the WLAN, what should be defined in your WLAN design software that will result in different requirements at varying locations o...

When performing a spectrum analysis walkthrough of a facility tor which you will be creating a WLAN design you detect an interferer What should you do?

While using a USB adapter attached to a USB hub and your laptop for protocol analysts you notice that the SNR is lower than expected. The USB adapter is an 802 11 ac 3x3 3 adapter...

When implementing multiple SSIDs to what is each SSID typically mapped in order to provide traffic management separately for each SSID?

An organization is implementing a new WLAN. They are upgrading a very old 802.11g network that only a few devices used Now. they expect more than 250 devices to use the new WLAN th...

You are designing a WLAN and nave been asked to recommend a security solution for the network The organization requires that 802 1X/EAP be implemented, but they do not have a PKI a...

You must perform a site survey that defines signal strength, throughput and latency. What kind of survey should you perform?

An organization has chosen to implement Wi-Fi 6E and operates in a regulatory domain allowing the use of all 6 GHz channels. Why can 40 MHz channels be used more easily in this net...

What is a typical characteristic of barcode scanners?

What document can be useful when determining client capabilities in a WLAN design project?

What inexpensive tool is capable of locating neighbor WLANs if that is your only need?

What are the two most common industry-standard protocols used to transport data from an AP to a Wireless LAN Controller?

Wh.ch one of the following options is a dedicated throughput testing application, usable on both the WLAN and LAN?

What is the most appropriate antenna which will require the least Intentional Radiator power for a point-to-point bridge link spanning 1200 meters?

What commonly used item can help lo prevent back pain during lengthy site surveys?

Which type of building material causes the most attenuation of Wi-Fi signals'?

What are the best practices for belter location accuracy when deploying Wi-Fi RTLS?

You have enabled IEEE 80211 FT in your WLAN infrastructure. You want to verify roaming between APs (two at a time) and determine If all of your end-points are capable of performing...

What should you do during the design process of a point to point bridge link to minimize CCI and ACl?

When creating a long-distance bridge link, it is important to know the channels in use by other networks on both ends of the link and within a reasonable range It is not as Importa...

What is the purpose of a Physical Installation Guide document?

What single tool, by design can be used to verify channel selection, encryption in use and number of APs above a specified signal threshold in a given location during deployment?

Before connecting, mounting and powering 213 total controller-based APs what action should be taken to ensure that they are configured by the controller once powered on and connect...

You have designed a WLAN with a plan for 87 APs m a large office building. The customer has informed you that the budget is not as large as they hoped and they can only purchase 53...

During the deployment of a WLAN the customer complains that the chosen locations for several APs are ruining the aesthetics of the building Instead of changing AP locations and req...

Install technicians are deploying a multi-floor WLAN that you have designed They have finished the first floor and all APs on that floor are powered on and functioning No APs on an...