JN0-362 Exam Questions
181 real JN0-362 exam questions with expert-verified answers and explanations. Page 4 of 4.
- Question #167
Which three statements are true regarding the show system switchover operational mode command? (Choose three.)
- Question #168
You have been asked to use a convention that allows for auto configuration of interface addresses. You are not allowed to use DHCPv6. What do you do?
- Question #169
You notice that the RID of your router is being taken from the address of your management interface. What could cause this scenario?
- Question #170
You have been asked to identify what the contributing routes are for route 204.7.15/21.Which command will show this information?
- Question #171
Which packet type does the router use to request up-to-date link-state information?
- Question #172
Which forwarding table designation is used to indicate that load balancing is working correctly?
- Question #173
Which two statements are correct regarding VPLS mesh groups? (Choose two.)
- Question #174
Which Layer 2 mechanism logically groups network nodes into separate broadcast domains?
- Question #175
Which two statements correctly describe the BGP community attribute? (Choose two.)
- Question #176
Click the exhibit. Customer 1 has experienced some hardware failures that erroneously transitioned some links into a forwarding state, as shown in the exhibit. In this scenario, wh...
- Question #177
Click the Exhibit. You are using OSPF as your IGP in your network. You have applied the OSPF configuration shown in the exhibit to router R1. Which statement is true in this scenar...
- Question #178
Click the Exhibit. On an MX Series device, you must enable routing between VLANs 100,200, and the Internet ge-5/1/0, and ge-5/1/2 are bundled into interface ae3. Ge-5/1/4, and ge-5...
- Question #179
You are configuring a default static route using the default preference value. You want to ensure that any static route that you configure in the future will be less preferred than...
- Question #180
You have recently configured MSTP on two switches in your network to participate in the same MSTP region. You issue the show spanning-tree mstp configuration command on both switch...
- Question #181
You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisit...
- Question #182
You own a small company and need to assign IPv6 addresses to your routers. Because you want to follow the guidelines spelled out in RFC 3177, you want to design your network with t...
- Question #183
Your customer would like to forward traffic using DLCI 600 and maintain Layer 2 information across a VPN.Which solution will meet these requirements?
- Question #184
You have two OSPF routers that are trying to form an adjacency. When you issue the command show ospf neighbor, you see that one router is in the loading state and the other is in t...
- Question #185
Which two events could cause the BGP Active state to appear? (Choose two.)
- Question #186
Click the Exhibit button. The policy shown in the exhibit has been configured and installed on your router. What is the result of applying this policy?
- Question #187
Which type of router can provide connectivity between areas in an IS-IS domain?
- Question #188
You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as defined in RFC 4364.Which three tasks must be performed before the provider network is...
- Question #189
By default, which BGP attribute is only compared when two route advertisements are received from the same neighboring AS?
- Question #191
An Ethernet bridge is configured such that all interfaces are in a single broadcast domain.Which two tasks does the bridge perform in response to receiving a frame with an unknown...
- Question #192
You have configured multiple IP-IP tunnels across your network to provide connectivity to remote sites.Which technique is used to help the IP endpoints in your network determine th...
- Question #193
You are asked to design a Layer 2 VPN service between service provider networks that needs Ethernet transport capabilities. The VPN should support two or three endpoints. Which Lay...
- Question #194
You are adding nonforwarding route reflectors to your network. Which three actions ensure that VPN routes are advertised properly? (Choose three.)
- Question #196
Which statement is true about the operation of Layer 2 VPNs?
- Question #197
Which two statements are true when configuring OSPF authentication? (Choose two.)
- Question #198
Which three statements are true about the BGP community attribute? (Choose three.)
- Question #199
An IS-IS level 1-only router is configured within a larger multilevel hierarchy. Which OSPF area type resembles the routing information in the L1 router's table?