HPE6-A86 Exam Questions

A network is configured with two 2930F switches as the aggregation layer. Each 2930F switch has ten connections. The network has twenty 2530 access switches connected to both aggre...

A security auditor asks whether you use any insecure management protocols to configure your CX-6200 switches from their factory default state. What can you tell them?

A Windows PC is not able to browse the Internet. Based on the output, what could be the problem?

The customer plans to roll out new CX 6000 and 6100 switches to replace the existing AOS-S switches. To make the deployment include fewer manual tasks, the customer has asked how t...

The customer requires the highest speed available using a single port link between a CX 6200 and a CX 6300 over a distance of 1 meter (3 feet). Which is the correct validated conne...

What are valid responses from a RADIUS server? (Choose two.)

In the partial example of the LLDP output below: What can be validated based on the provided output?

How many broadcast domains are shown in the diagram below?

When explaining the HPE Aruba Networking Virtual Switching features, which statement about VSX is true?

New IoT devices cannot obtain an IP address from a DHCP server (10.200.1.51). Based on the output below, what should you configure to resolve the issue?

What is the method for setting up an HPE Aruba Networking CX 8100 switch using an Android device, and which is recommended for ease of use?

A retail store chain customer is replacing 1,479 AOS-S switches with HPE Aruba Networking CX 6000 switches. The customer is interested in utilizing ZTP to provision the new switche...

Which of these is a configurable VLAN on a CX switch?

A technician installed a new 550 series access point, which is cabled back to a CX 6000 series switch. However, there are no lights on the AP. What could cause this?

Which user group exists by default on a CX 8400 series switch?

How do you configure an IP address for the management interface on a CX 6300?

What is considered a secure protocol?

Which is at the Transport Layer of the OSI model?

A newly connected 500R series access point is not visible in HPE Aruba Networking Central. You have run the following commands to troubleshoot. Based on the output, what could be t...

Which commands can ensure the current configuration persists after a reboot? (Choose two.)

Which statement is true when creating VLANs on an HPE Aruba Networking CX switch?

You have access to the CLI of an HPE Aruba Networking CX switch. How can you output the switch make, model, and serial number displayed on the session?

Which firewall port needs to be opened between your Network Monitoring System and CX switches to collect monitoring data using SNMP?

Which protocols can be used to control administrative access to HPE Aruba Networking OS-CX switches? (Choose two.)

A customer requires a network upgrade to replace their existing core switches. The new solution must support 100G speeds to the aggregation layer, with the ability to scale to a 12...

Based on the given output: Which HPE Aruba Networking CX switch can be used to create this configuration?

Which statement is true given the IP address 10.64.0.240 and subnet mask 255.255.254.0?

You are checking the interface details for an Access Point that cannot reach HPE Aruba Networking Central. After reviewing the following output, which statement is true?

Which two benefits does QoS provide? (Choose two.)

What does the show logging command display on an Aruba switch?

A switch port is up, but no traffic is being forwarded. What could be a possible reason?

At which layer of the OSI model does data segmentation occur?

When multiple routes exist to the same destination, which would be installed in the routing table?

Which attributes are true about UDP? (Choose two.)

Your colleague is installing a new HPE Aruba Networking CX 8100 switch in a data center in the default configuration. You monitor the peer switch port 1/1/1 status, connected with...

You are trying to configure VSF on a pair of CX 8325 series switches. What would cause the following error? Switch-1(config)# vsf member 2 Invalid input: vsf Switch-1(config)#

The external DHCP server is configured with the IP address 192.168.1.100. The HPE Aruba Networking CX 6300M VSF is the L3 gateway for VLAN 200 clients, which should receive an IP a...

A customer is planning a replacement of their current 2930F switches, which are configured using VSF stacking. The proposed switches are CX 6200 models. What is the key difference...

Based on the example below: What happens to the member status state if member 1 reboots?

Which Aruba management tool allows for REST API-based automation and scripting?

What is the default subnet mask for an IPv4 Class C network?

A company recently deployed an Aruba switch and configured Link Aggregation Control Protocol (LACP) between two switches to improve bandwidth and redundancy. However, some links ar...

How can an administrator verify that an Aruba switch is forwarding traffic correctly?

A customer is about to connect a new CX 6200 switch using ports 1/1/47 and 1/1/48 to an existing 5406R in a VSF configuration. The VSF is already configured with the following sett...

You are planning a 40Gbps link between two sites 35km apart. What type of cable will be required?

What describes the use of the Network Analytics Engine?

Based on the example below: How is the VSF integrity verified if the VSF links between members 1 and 3 + 2 and 3 are disconnected?

How do you configure an in-band management IP address for the CX 4100i switch?

A customer has a skilled internal DevOps team with extensive Python programming knowledge. Which HPE Aruba Networking CX switches would you recommend for the customer to support se...

A customer has configured a CX 6200F VSF stack already in use. You are given the following information on the setup: What steps are required to add a new member to the solution?