HP2-Z33 Exam Questions
74 real HP2-Z33 exam questions with expert-verified answers and explanations. Page 1 of 2.
- Question #1
An administrator changes the setting for VLAN 200 on an HP 830 switch from tagged to untagged. How will this change affect the traffic sent over VLAN 200?
- Question #2
A branch location is deploying standalone wireless access points (APs). What can be used to configure and manage these APs? (Select two.)
- Question #3
When accessing the wireless network in 802.1X with EAP-TLS, what do the user endpoints require?
- Question #4
An organization wants to upgrade their wireless network to allow employees to connect using their 802.11ac enabled devices. Which HP access points meet this requirement?
- Question #5
A network administrator configures 802.1X authentication on a wireless network set with an HP 830 Unified Wired-Wireless Controller. The administrator configures a RADIUS scheme na...
- Question #6
An organization implements an N+1 redundancy for its access controllers (ACs). When the primary AC fails, the access points (APs) successfully fail over to the standby AC. However,...
- Question #7
Refer to the exhibit. What does AP Echo Interval of 10 seconds indicate?
- Question #8
A customer is planning to deploy HP MSM466-R access points in an extreme cold environment to interconnect to the Unified Wired-WLAN Module in the HP switch. Which requirement is ne...
- Question #9
What is an advantage of the HP IMC Wireless Service Manager (WSM)?
- Question #10
In 802.11n, what does fat channel intolerance indicate?
- Question #11
When does DHCP fingerprinting of endpoints occur within an HP BYOD solution?
- Question #12
From the perspective of one MSM controller in a network operating Wireless Mobility (L3 roaming), what is the name given to a home client that has roamed to another subnet?
- Question #13
In addition to the priority level, which other QoS choices are available? (Select three.)
- Question #14
What is the HP implementation of a Wireless Distribution System (WDS)?
- Question #15
Where can a network administrator check for successful authentication in User Access Manager?
- Question #16
A company is deploying HP MSM 802.11n Dual Radio Access Points (APs). Connected clients will be a combination of 802.11b, g, and n devices. The company does not expect 802.11a devi...
- Question #17
Which action does the Wireless Intrusion Prevention System (WlPS) take when it detects that a device is sending frames with a fixed initialization vector?
- Question #18
An organization's security policy mandates the use of 802.1X port based authentication. The organization's security policy also mandates that before an employee's personal device c...
- Question #19
The Wireless Intrusion Prevention System (WIPS) determines that a client has exceeded the maximum number of authentication requests that a client should make in the allowed period....
- Question #20
An organizations BOYD security policy states that if an employee wants to connect to the company's wireless network with their personal devices, they must meet the following requir...
- Question #21
HP has released a new version of an access controller software package file. How does the network administrator activate the new software version?
- Question #22
It is Monday morning, and no one can connect to the wireless network. The network administrator suspects that the access controller's certificate may have expired and is no longer...
- Question #23
Which command configures the management IP address on a WLAN controller?
- Question #24
An administrator wants to configure authentication on the HP 830 switch ports that connect to wireless access points. The company policy requires all wireless users to be authentic...
- Question #25
Refer to the exhibit. An engineer is installing a new access point (AP). The AP has successfully acquired an IP address. The engineer can ping the access controller (AC) from the A...
- Question #26
Refer to the exhibit. The access controller (AC) has configured session-mode load balancing. The maximum number of sessions is configured as 5. The maximum session gap is configure...
- Question #27
Which factors impact the calculation of the Effective Isotropic Radiated Power (EIRP)?
- Question #28
Refer to the exhibit. What does the Auth Mode enable?
- Question #29
Refer to the exhibit. What is the primary advantage of enabling SSID Hide?
- Question #30
To allow user access for corporate employees, a network administrator sets an SSID named CORPORATE using an HP Unified Wireless solution. The administrator wants these security enh...
- Question #31
You have been asked to deploy a guest wireless service within an A-Series solution in the reception area of a marketing firm. The clients associated with the guest service should b...
- Question #32
IT must implement a wireless LAN with encryption using an HP A-Series wireless access point. Which component of a wireless service should be configured?
- Question #33
A publishing company is currently using Wired Equivalent Privacy (WEP) to secure its wireless network. The IT staff would like to transition to 802.11i but they have many clients t...
- Question #34
In an HP BYOD solution, what does DHCP fingerprinting provide?
- Question #35
A network administrator sets up the DHCP relay on an HP Comware Layer 3 device that forwards IP traffic between the VLANs associated with the wireless SSID with these commands. Wha...
- Question #36
A business deploys a wireless network that includes an HP 10500/7500 module and 120 access points (APs). They plan to increase the number of APs to 250. Which step must be performe...
- Question #37
A corporate user accesses a corporate network on SSID CORPORATE. The user endpoint is set up for 802.1X in PEAP-MSCHAPV2. - HP BYOD is implemented. - Wireless is set up on a HP Uni...
- Question #38
Which statement is correct about security on a wireless network?
- Question #39
What is the purpose of Transparent MAC authentication?
- Question #40
When is a User Access Manager certificate required?
- Question #41
Refer to the exhibit. A client can roam successfully between AP1 and AP2. However, the client is unable to roam between AP2 and AP3. What could be the problem?
- Question #42
A network administrator configures an HP BYOD solution. To authorize guests to register their endpoints, the network administrator sets up components of the Onboarding process. Whi...
- Question #43
Refer to the exhibit. A company wants to connect a mid-size branch office to their corporate location. An HP 10500/7500 Unified Wired-Wireless module is deployed at the corporate l...
- Question #45
Which feature must be enabled globally on the VLAN of the wireless interface to enable multicast optimization?
- Question #46
What is the maximum data rate that a 2x3 Ml MO 802.11 n enabled device can transmit at?
- Question #47
Which command allows an administrator to access the HP 830 switch CLI from the controller?
- Question #48
Which authentication mechanism uses a RADIUS server in an HP BYOD solution?
- Question #50
A company plans to deploy an HP MSM wireless network. The company currently has a RADIUS server that is used to control employee access to the company's Intranet from wired clients...
- Question #51
Which action can a guest manager perform?
- Question #52
How can a network administrator set up User Manager (UAM) redundancy?