HP0-S35 Exam Questions
206 real HP0-S35 exam questions with expert-verified answers and explanations. Page 2 of 5.
- Question #55
New virtual Connect Flex-10 modules are installed in an HP BladeSystem c3000 chassis. While creating the profiles and assigning them to networks, two profile assignments fail. The...
- Question #56
At a customer meeting, a concern was raised about IT infrastructure security management. In planning the solution for this concern, which critical area should be addressed?
- Question #57
What is the correct UEFI shell command to check the boot profile used for ignite/UX on an HP integrity BL860c i2 blade server?
- Question #58
Before returning an SSD attached to a SMART Array controller in a Blade system in warranty, what must be performed?
- Question #59
What is a possible reason for the Unknown port status in Fabric-A in the screenshot shown?
- Question #60
How can the administrator account password and DNS settings of the HP Virtual Connect Flex 10 Ethernet Module be restored to the original factory defaults?
- Question #62
Which method should you use to upgrade the Intelligent Provisioning partition on a BL460c Gen8?
- Question #63
How can an administrator set up a default root password for Red Hat Linux installations using Server Deployment?
- Question #64
Definition of RPO HP HP0-S35 Exam
- Question #65
What Filessytems does ESXi 5.0 support?
- Question #66
What is the definition of a Hot aisle?
- Question #67
A customer purchased a 10700 G2 rack and with a fully populated C7000 and HP UPS R7000 what is the optimal position for the UPS and C7000 so the rack will be balanced?
- Question #68
How would you perform NIC teaming in a HP environment with Windows Server 2008 R2?
- Question #69
A customer wants to enable load balancing in a Vmware environment ?what is the best route to HP HP0-S35 Exam do this?
- Question #70
How does virtual connect refer to fiber channel technology?
- Question #71
In this scenario why is the user not connecting to the EVA? (Picture of Flexfabric module connected to a HP procurve switch on X1, X2 and EVA on ports X5 and X6)
- Question #72
What protects against 8 ?bit parity mode error detection?
- Question #73
What is required to configured Lockstep mode on a Bl460 Gen 8?
- Question #75
What memory protection is available to a BL460c Gen8?
- Question #76
What is required on a server to use Server Deployment in Insight control? (Choose 3)
- Question #78
What color is the notation in Insight control if a Fan fails?
- Question #79
You are looking to expand a raid what command is needed to do this?
- Question #80
You want to create a online spare of a Raid 1 what is needed in order to accommodate this?
- Question #81
What is something that HP agentless management can monitor and proactively notify prior to failure? (Choose Three)
- Question #82
What is the speed of the network on the ILO management port in Gen 8?
- Question #83
What are some advantages of ILo4 versus Ilo3
- Question #84
What are troubleshooting areas for a FC EVA array?
- Question #85
What is required for an iPDU to collect information?
- Question #86
Which tools can you use to design SAN infrastructure connecting to a 3rd party array? (Choose Three)
- Question #87
A customer has two C3000's with flexfabric modules and does not have VCEM what would be the recommended for mac addressing?
- Question #88
Which memory protection is supported on a BL460c Gen8 Blade Server? (Select two)
- Question #89
What is the definition of Recovery Point Objective (RPO)?
- Question #90
An HP BladeSystem c7000 Insight Display backlight is flashing. What can cause this?
- Question #91
What are the major advantages of the GUID Partition Table (GPT) over the Master Boot Record (MBR)?
- Question #92
Which component is only required on the monarch module of an HP Integrity i2 server?
- Question #93
What can you sue to transfer information over a power distribution infrastructure consisting of an iPDU and extension bars?
- Question #94
Before implementing a solution, which HP tool helps facility teams and IT staffs size power infrastructure to meet HP BladeSystem solution requirements?
- Question #95
A customer bought a new HP BladeSystem c7000 enclosure with HP Flex-10 interconnect modules. Which HP BladeSystem Installation and Startup Sevice is needed to implement the network...
- Question #96
In an HP BL460c Gen8 server, which NIC RBSU personality setting allows the Converged Network Adapter to connect to the Fiber Channel storage?
- Question #97
A customer has a c7000 blade enclosure with several HP ProLiant blade Gen8 server installed in an HP10636 G2. The customer ordered an HP UPS R8000\3 for this blade configuration an...
- Question #98
Which settings can you configure using EBIPA? (Select two)
- Question #99
A customer wants to add a second dual port Fiber Channel adapter to a BL460c Gen8 Server in an HP BladeSystem?
- Question #100
An administrator is concened about losing the enclosure setting and configuration if the Onboard Administrator (OA) fails. What is the best available option?
- Question #101
Which components are required for Insight Control Server Deployment to work correctly? (Select two)
- Question #102
What is used to increase the logical drive size in an HP Smart Array controller installed in an HP ProLiant server?
- Question #103
In a P4000 system, which Network RAID level is required to power off the drive in the Central Management Console before removing it?
- Question #104
After a power failure, how long will the data be retained on the cache of an FBWC of a Smart Array Controller?
- Question #105
How can you access the memory DIMM Serial Presence Detect (SPD) data failure log in an HP ProLiant BL460c Gen8 server?
- Question #106
What is the network speed of the new iLO in ProLiant DL380p Gen8 server?
- Question #107
What is the fastest way to verify SAS drive firmware before installing an operating system? HP HP0-S35 Exam