GB0-363 Exam Questions

It is necessary to know the protocol system used in the network. developed by IBM in 1970s is widely applied in the finance network.

The hierarchical network model consists of .

Which of the following is/are used to solve the shortage of VLANs in the VLAN planning?

The hierarchy of LAN topology consists of .

The multicast address used by VRRP is .

The DHCP Relay security feature must be configured on the gateway where DHCP Relay is enabled. If the DHCP Relay device is not the gateway, packet forwarding is not affected.

In an MSTP region, all switches must support the MSTP. There is not such a switch that supports RSTP or STP only.

The DHCP message is encapsulated by .

The access authentication modes supported by the SecPoint include .

IPSec encapsulate data into a new IP packet in .

The encryption algorithm can be classified into based on the key type.

In an OSPF network, the routes in the backbone area can be distributed to the non-backbone areas after being aggregated.

The static routing is applicable for .

Which of the following multicast addresses is/are dedicated to the OSPF routing protocol?

Which of the following descriptions about OSPF route filtering is/are correct?

The most popular IGP at present is .

The community name still exists in SNMPv3, but the SNMPv3 security mechanism does not depend on it any longer.

Which of the following can be used for packet classification?

Both traffic policing and traffic shaping can limit traffic speed.

Which of the following OSPF network types are supported by the Frame Relay point-to-multipoint sub-interface?

Which of the following should be used in the network where two equipments interconnect through multiple PPP links?

The maximum rate of PSTN dialing connection is .

The circuit simulation of ATM uses the CBR service.

For the sake of security and maintenance cost, which of the following should be used to provide device authentication in a large-sized and middle-sized IPSec VPN?

Which of the following descriptions about L2TP VPN design is/are correct?

PIM-SM may not need RP.

In the PIM protocol, which of the following factors should be considered first when a sender is selected by using the ASSERT mechanism?

Which of the following addresses should not be aggregated?

Which of the following should be used in the loopback interface address planning?

The advantages of the IPv6 automatic tunnel such as ISATAP and 6to4 are .

As in the IPv4 network, to save address in the IPv6 network, we should assign an appropriate prefix length to the router interface connecting to the host according to the quantity...

The equipment with carrier-class reliability refers to the equipment that supports large capacity, non-stop running, key module redundancy, and high stability.

The multicast routing protocol supports equal-cost routes.

During setting Multicast TTL limit, the TTL threshold of the border router is set to 15. To prevent multicast data crossing the border router the maximum TTL of the multicast sourc...

Which of the following descriptions about BGP attributes is/are correct?

Which of the following protocols is a EGP?

There are three lines between the branch and the central office of a bank. It requires that different services use different links and needs mutual backup. Which of the following d...

Which of the following descriptions about BGP route importing is/are correct?

Which of the following descriptions about BGP is/are correct?

The Next-hop attribute of BGP can be changed between EBGP peers.

Which of the following is/are used to avoid the problem caused by connecting an RSTP edge port with a switch?

The RSTP does not have TCN PDU.

Which of the following descriptions about VRRP is/are wrong?

The VLAN division principles include .

CIST is a concept in the MSTP. It is a single spanning tree so that it cannot provide load balancing.

Which of the following routing protocols uses the Distance-Vector algorithm?

During OSPF route aggregation, we should aggregate the interconnecting addresses, the user addresses and the loopback addresses.

Which of the following routing protocols uses the link state algorithm?

RIPv1 and RIPv2 are featured by .

The superiority of RIPv2 to RIPv1 includes .