FCSS_SDW_AR-7.4 Exam Questions

You want FortiGate to use SD-WAN rules to steer local-out traffic. Which two constraints should you consider? (Choose two.)

Refer to the exhibit that shows a diagnose output on FortiGate. Based on the output shown in the exhibit, what can you say about the device role and how it handles health checks?

Refer to the exhibit. Which statement best describe the role of the ADVPN device in handling traffic?

Refer to the exhibits. The first exhibit shows the SD-WAN zone HUB1 and SD-WAN member configuration from an SD-WAN template, and the second exhibit shows the output of command diag...

As an IT manager for a healthcare company, you want to delegate the installation and management of your SD-WAN deployment to a managed security service provider (MSSP). Each site m...

You have configured the performance SLA with the probe mode as Prefer Passive. What are two observable impacts of this configuration? (Choose two.)

Refer to the exhibit. Which two conclusions can you draw from the output shown? (Choose two.)

Refer to the exhibits. The interface details, static route configuration, and firewall policies on the managed FortiGate device are shown. You want to configure a new SD-WAN zone,...

Refer to the exhibit. How does FortiGate handle the traffic with the source IP 10.0.1.130 and the destination IP 128.66.0 125?

Your FortiGate is in production. To optimize WAN link use and improve redundancy, you enable and configure SD-WAN. What must you do as part of this configuration update process?

Refer to the exhibits. The administrator configured a device blueprint and CLI scripts as shown in the exhibits, to prepare for onboarding FortiGate devices in the company's stores...

The administrator uses the FortiManager SD-WAN overlay template to prepare an SD-WAN deployment. Using information provided through the SD-WAN overlay template wizard, FortiManager...

You used the HUB IPsec_Recommended and the BRANCH IPsec_Recommended templates to define the overlay topology. Then, you used the SD-WAN template to define the SD- WAN members, rule...

As an MSSP administrator, you are asked to configure ADVPN on an existing SD-WAN topology. FortiManager manages the customer devices in a dedicated ADOM. The previous administrator...

Refer to the exhibit, which shows the SD-WAN rule status and configuration. Based on the exhibit, which change in the measured latency will first make HUB1-VPN3 the new preferred m...

Refer to the exhibits, which show the configuration of an SD-WAN rule and the corresponding rule status and routing table. The administrator wants to understand the expected behavi...

Refer to the exhibit. The exhibit shows the BGP configuration on the hub in a hub-and-spoke topology. The administrator wants BGP to advertise prefixes from spokes to other spokes...

Refer to the exhibit. The exhibit shows the details of a session and the index numbers of some relevant interfaces on a FortiGate device that supports hardware offloading. Based on...

The FortiGate devices are managed by ForliManager, and are configured for direct internet access (DIA). You confirm that DIA is working as expected for each branch, and check the S...

Refer to the exhibit. The administrator configured the SD-WAN rule ID 4 with two members (port1 and port2) and strategy lowest cost (SLA). What are the two characteristics of the s...

Refer to the exhibit. The exhibit shows the health-check configuration on a FortiGate device used as a spoke. You notice that the hub FortiGate doesn't prioritize the traffic as ex...

Refer to the exhibits. The exhibits show an SD-WAN event log, the member status, and the SD- WAN rule configuration. Which two conclusions can you draw from the information shown?...

Which three factors about SLA targets and SD-WAN rules should you consider when configuring SD-WAN rules? (Choose three.)

Refer to the exhibit that shows an SD-WAN zone configuration on the FortiManager GUI. Based on the exhibit, how will the FortiGate device behave after it receives this configuratio...

Refer to the exhibits. The exhibits show the SD-WAN zone configuration of an SD-WAN template prepared on FortiManager and the policy package configuration. When the administrator t...

When you configure FortiGate for SD-WAN, what is the impact when you assign a priority to the SD-WAN members?

Refer to the exhibit. To check the status of an SD-WAN topology using the FortiManager SD- WAN monitor menus, you place your mouse next to branch1_fgt and receive the output shown...

An MSSP uses FortiManager to manage the FortiGate devices of its customers. The administrator grouped the devices for each customer in different ADOMs. For customer A, you configur...