EW0-300 Exam Questions
152 real EW0-300 exam questions with expert-verified answers and explanations. Page 2 of 4.
- Question #53
The default OSPF router dead interval for Extreme Networks switches is
- Question #54
What is the CLI command to put vlan purple?on physical port 2 into STPD oak?in EMISTP mode?
- Question #55
Which of the following ways can result in the election of a new ESRP Master in an Extreme ESRP network when the switches are configured with the default election algorithm?
- Question #57
Which CLI command enables all multicast traffic to multicast routers only?
- Question #58
Which of the following items is included in a DVMRP routing table.
- Question #59
Select the statements that apply when you compare and differentiate VRRP and ESRP.
- Question #61
in IS-IS level 1/2 routers act as border routers to their respective areas, providing connectivity to other areas.
- Question #62
In a stable OSPF network, all OSPF routers in the same area must have the same LSDB contents.
- Question #63
Manual replication of saved images and configurations from the master MSM64i to the slave MSM64i on the BlackDiamond 6804 is done with the synchronize command. However execution of...
- Question #64
Select the correct statements related to IP Multicast?
- Question #65
The Skew time in VRRP is used to ensure that two back-up routers do not switch to master state at the same time an case of a fall-over situation.
- Question #66
The LSP overload bit in IS-IS can be set by a router to inform neighbor routers that this routers link state database is not complete so the others can ignore this unreliable route...
- Question #67
By default, the OSPF routerID for an Extreme switch is selected automatically, and uses the lowest IP address of the router interefaces.
- Question #68
The DHCP, HTTP and RADIUS functions that are required for Netlogin are supported on the Extreme Networks switch, where RADIUS function is restricted to client mode.
- Question #69
What does the QoS Monitor show by default when using the command show port 1 qosmonitor?
- Question #70
In OSPF, when you configure an Extreme switch with router priority of 0, what happens?
- Question #71
An Ethernet Automatic Protection Switching (EAPS) domain relies on a control VLAN. That control VLAN must be tagged with an 802.1Q tag.
- Question #72
What does the abbreviation DVMRP stands for?
- Question #73
IS-IS routing uses two levels of hierarchical routing level 1 and level 2. A level 1 router has full knowledge of the topology in the whole routing domain in a network with multipl...
- Question #74
When you configure EAPS the following must apply.
- Question #75
Which of the following is the default ESRP priority setting for an Extreme switch?
- Question #76
With two MSM64i modules in a BlackDiamond 6808, when you save the switch configuration, it is saved to all MSM64i modules and if you download a new ExtremeWare image, the image is...
- Question #77
Extreme Networks ? chipset switches support the Radius feature. The switch becomes a radius server after enabling this feature and proper configuration
- Question #78
When configuring a Summit 5i for OSPF routing, it is recommended to manually configure the OSPF router-id rather than setting the router-id set to automatic.
- Question #79
What is the function of a Bootstrap Router?
- Question #80
Is it possible to configure a single physical port into different STPD's?
- Question #81
What is true of a Rendezvous Point in PIM-DM?
- Question #82
Unlike VRRP, the eExtreme Standby Router Protocol provides redundancy at both the data link and network layers of the ISO-OSI seven-layer model.
- Question #83
Which of the following is not advertised in an OSPF Link State Advertisment?
- Question #84
Limit-learning allows you to specify a maximum number of source MAC addresses per port/vlan. What happens when a number of dynamically learned MAC addresses time-out after the limi...
- Question #85
Select all terms that relate to IP multicast routing.
- Question #86
The whole Internet currently supports IP Multicast with PIM dense mode.
- Question #87
The steps for OSPF to begin routing packets are
- Question #88
IGMP v1 supports the leave group message.
- Question #89
Which CLI command would you use to configure vlan tracking towards vlan engineering for an ESRP protected VLAN manufacturing?
- Question #90
A priority setting of 255 in VRRP makes the switch ineligible to become the master switch.
- Question #91
What does the abbreviation PIM stands for?
- Question #92
By default all VLANs are assigned to QoS profile QP
- Question #93
Choose the one characteristic below that does not relate to DVMRP.
- Question #94
All Extreme switch products support the standard 802.1p priority bits that are part of a tagged Ethernet frame.
- Question #95
In general IS-IS allows routing of both IP and OSI packets. What type of Implementation does ExtremeWare support?
- Question #96
_________is an ESRP option that allow(s) multiple VLANs to be controlled by a single instance.
- Question #97
What are te differences between a Summit 481 and a Summit 48si? Choose all that apply
- Question #98
An Alpine 3808 switch can operate without the SMMi management module?
- Question #99
OSI stands for Open System Interconnection, which is known as an International standard protocol architecture.
- Question #100
EAPS is an Extreme Networks proprietary solution and is only supported on Ethernet fbier links with a speed of 100 Mbps.
- Question #101
IS-IS is a designed to work in conjunction with
- Question #102
A TCP type ACL that uses the permit-established keyword filters out SYN packets in one direction.
- Question #103
A type of OSPF router that functions to connect two autonomous systems together is called
- Question #104
When you create an ACL entry on Summit 48i switch it works in the following way