EW0-300 Exam Questions
152 real EW0-300 exam questions with expert-verified answers and explanations. Page 1 of 4.
- Question #1
Extreme Networks IS? Chipset switches allows you to run simultaneously the Radius and Tacacs+features.
- Question #2
OSPF requires that all areas attach directly to the backbone area, and that all attachments are made with a direct physical connection.
- Question #3
An Ethernet Automatic Protection Switching (EAPS) domain relies on a control VLAN. The ports in that control VLAN ports must be tagged, and participating in the ring only.
- Question #4
In SLB, Port Translation Mode is similar to Translation Mode,except that in Port Translation Mode the physical Port where the node connects to must be configured as a Fast Ethernet...
- Question #5
In PIM sparse mode the Bootstrap Router election is based on the highest IP address.
- Question #6
ESRP-enabled switches can utilize either an IP address or an IPX net ID for their protected VLANs.
- Question #7
An IP-only IS-IS router (or "IP-only" router) is defined to be
- Question #8
On an Extreme Networks switch, how many bits comprise an OSPF area ID?
- Question #9
What is the RP-set?
- Question #10
The majority of Extreme Networks switches have a dedicated out of band management port and VLAN. The 10/100BASE-TX Ethernet management port allows you to communicate directly to th...
- Question #11
Which of the following statements fit the description of PIM sparse mode? (choose three that apply)
- Question #13
What is the CLI command you would use to configure a VLAN to be protected by ESRP?
- Question #14
Extreme Ware 7.0 can support which OSPF authentication on a per VLAN basis
- Question #15
How does an IGMP router learns about the existence of hosts in multicast groups
- Question #16
Although you can specify sequence numbers for different ACL entries, the Summit 1i switch checks incoming traffic on a match with the ACL entries in the order of their time in conf...
- Question #17
What is the meaning of the IEEE 802.3 SNAP field in an Ethernet frame?
- Question #18
DVMRP is similar to OSPF in that it is Link State based.
- Question #19
Traffic involved with Policy based QoS is handled by the switch its CPU.
- Question #20
Within VRRP the election process of becoming the master switch takes place with the following precedence Step 1 The switch with the virtual router IP address becomes the master swi...
- Question #21
A QoS building block that defines a class of service by specifying traffic behavior attributes like bandwidth is called
- Question #22
Dealing with access control lists on Extreme Networks switches it is not required to manually configure the default rule.
- Question #23
Which CLI command would you use to determine the IP routes that are tracked by ESRP?
- Question #24
When SSH2 is configured and enabled on a Summit 7i switch, telnet is automatically disabled.
- Question #25
The following MAC address, 00.00.5E 00.01.0A represents
- Question #26
An Extreme switch connected to a network of Extreme Switches running ESRP is called an ESRP-aware switch due mainly because
- Question #27
In Extreme Ware what is the normal ACL behavior for incoming traffic when there is no default rule configured?
- Question #28
Health checking is used in SLB to determine the health of nodes by activity poling these nodes. The default health check called ping-check will keep working when the switch has an...
- Question #30
The type of OSPF LSAs that are sent out within an automous system by an ASBR to advertise extreme routes are
- Question #31
What are the advantage/s of using integrated IS-IS as a routing protocol?
- Question #32
What is true when different VLAN that are protected by Spanning Tree share the same physical ring topology?
- Question #33
Identify the Summit chip switch that provides the following port density, 48 10/100 Ethernet ports and two unpopulated GBIC ports.
- Question #34
A QoS policy is the result when you assign a traffic grouping to a QoS profile when configuring QoS on a Summit1i switch.
- Question #35
IS-IS is an exterior gateway protocol?
- Question #36
What is an IGP protocol other than OSPF that uses the Dijkstrat's SPF routing algorithm?
- Question #37
The Alpine 3802 switch contains a 3-slot chasis that can be populated with up to three I/O modules.
- Question #38
Radius on Extreme Networks IS? Chipset switches allows validation for the following switch access methods
- Question #39
Select the statements that are true for IP multicast?
- Question #40
An OSPF router connected to a RIP network & performing route redistribution is considered
- Question #41
What is the maximum number of ACL rules supported on an Extreme Networks Summit7i switch without the default rule?
- Question #42
What configuration is send when you upload a configuration from a Summit 1i switch to a TFTP server
- Question #43
DVMRP uses the same IP packet header as IGMP to exchange routing datagram.
- Question #44
Is it possible to create multicast STPD on a switch?
- Question #45
Which of the following IP destination addresses can be used for multicast streams?
- Question #46
The Summit 7i switch supports how many queues per interface?
- Question #47
When a PIM-SM router wants to receive a Multicast stream, it
- Question #48
IP Multicast uses TCP socket number 1812 for packet exchange
- Question #49
You have manually set the router-id now in order for an Extreme switch to use the numeric highest IP interface address as the OSPF router id on the next OSPF initialization, you wi...
- Question #50
Select one of the known limitations of DVMRP?
- Question #51
The IS-IS Routing Protocol has been developed in ISO to provide routing for pure OSI environments.
- Question #52
The CLI Command configure ospf delete vlan all? Will do the following on an Extreme switch.