EW0-200 Exam Questions
225 real EW0-200 exam questions with expert-verified answers and explanations. Page 2 of 5.
- Question #51
in 802.1D mode ExtremeWare supports a VLAN being a member of up to 128 STP domains.
- Question #52
Prior to downloading a new software image to an Extreme switch using the network, you are required to place the software image in a file on a TFTP server that is accessible on the...
- Question #53
The CLI command to disable poison reverse on an Extreme switch is:
- Question #54
RIP is a routing protocol that scales to a limit. What is the maximum number of supported hop counts?
- Question #55
The IP ROUTING field indicates whether IP forwarding has been enabled or disabled when the CLI command: show ipconfig is entered.
- Question #56
After using the disable web command you later issue the show session command and see the following: How was it possible for someone to login with ExtremeWare Vista?
- Question #57
Which statement is true?
- Question #58
Which CLI command should be used to configure the link cost for RIP?
- Question #59
Given the following diagram, which command would you use to send a switch configuration file from the TFTP server to the switch?
- Question #60
ExtremeWare automatically compensates for the increase in frame size when enabling vMAN tagging.
- Question #61
In order to span multiple VLANs across Extreme switches, the protocol EDP must be enabled.
- Question #62
The following applies when you execute a scheduled incremental download from a TFTP server.
- Question #63
The Extreme switch ASIC look-up Host Table containing IP host routes, outbound VLAN interfaces and ports is called:
- Question #64
What is the maximum specified distance for Extreme LX-100 fiber optic GBIC?
- Question #65
What is the default 802.1Q Tag Protocol ID used by Extreme Networks switches?
- Question #66
ExtremeWare provides two methods, RADIUS and TACACS+, to authenticate users who login to the switch. However, you cannot simultaneously enable the switch for both methods.
- Question #67
The modular Alpine 3808 has a capacity of 64Gbps and can forward 48 million packets per second.
- Question #68
In ExtremeWare, active VLANs that are configured with ports and an IP address and configured to forward IP and run a routing protocol will have their subnet advertised.
- Question #69
What happens when one executes the CLI command: unconfigure switch all?
- Question #70
The CLI Command ?7KH&/,&RPPDQGdisable learning ports 1?will do the following on an Extreme switch:
- Question #71
What command will provide you with information on SNMP statistics and SNMP access attempts?
- Question #72
A Bridge divides a network into:
- Question #73
Which of the following is a predefined protocol filter in an Extreme Switch?
- Question #74
Which CLI command would have caused the following if executed?
- Question #75
What is the broadcast address for 192.168.1.49/30?
- Question #76
When enabling load sharing in an Extreme switch, only a single switch must be configured. The switches will auto-negotiate the port sharing settings via the EDP protocol.
- Question #77
Which is not a tunable configuration option for STP?
- Question #78
Which of the following can generate route entries for the IP route table to become populated?
- Question #79
The acronym UDP stands for:
- Question #80
If you change and then forget the only remaining password for the CLI Administrator account ability to log on to an Extreme switch, how can you recover the password without loosing...
- Question #81
Which one of the following can populate an IP Route Table with its route entry on an Extreme switch?
- Question #82
The RFC 1918 describes the use and benefits of IP address space for private networks. The following IP address 10.10.60.254/23 can be considered as a valid private IP address.
- Question #83
There can be only one frame transmitted at a time on a traditional CSMA-CD Ethernet network. What is the result when more frames are sent at the same time?
- Question #84
Each IP address and mask configured for a VLAN must represent a unique IP subnet. However, the VLAN aggregation option allows you to use the same IP subnet on different VLANs.
- Question #85
What information is described by the IEEE 802.2 standard?
- Question #86
Extreme Networks switches build their forwarding database from the incoming packet field information containing the:
- Question #87
How could you verify that MAC address learning is disabled for ports 1 to 8 on a Summit7i switch?
- Question #88
ICMP traffic on a Summit 1i switch is always handled in hardware at wire-speed by the ASIC.
- Question #89
The maximum number of OSPF virtual links that an Extreme Summit1i switch can support is 32.
- Question #90
SNMP access to a Summit 48si switch can be limited by the following methods:
- Question #91
Extreme switches learn source MAC addresses and perform bridging based on the destination MAC address of incoming Ethernet frames.
- Question #92
Which CLI command will you use to change the CLI prompt from the default display to Switch02?
- Question #93
A 802.1Q tag is a marker inserted between the source and destination MAC addresses fields of the Ethernet frame.
- Question #94
What CLI command is used to disable learning of incoming RIP routes on an interface?
- Question #95
What is the maximum number of IP host addresses that fit in this network 172.168.128.96/27?
- Question #96
ExtremeWare does not allow any configuration changes for the relative route priority values.
- Question #97
In an Ethernet LAN, Layer 2 broadcasts reach every device within the same broadcast domain and may cause bandwidth, congestion and delay issues.
- Question #98
What is true when VLAN corporate shows a protocol field with the value of NONE.
- Question #99
What industry specification defines the ability to associate multiple VLANs on a single Ethernet link and is supported on Extreme Networks switches?
- Question #100
If an asterisk (*) appears in front of the ExtremeWare command-line prompt, what does it indicate?