EW0-200 Exam Questions
225 real EW0-200 exam questions with expert-verified answers and explanations. Page 1 of 5.
- Question #1
In RIP, poison reverse processing means that:
- Question #2
How would you create a VLAN named corporate using the CLI command?
- Question #3
When you type in the history command, the switch will show you the previous 49 commands. Using the arrow up/down key you can retrieve such a command.
- Question #4
What is the maximum number of simultaneously active protocol filters in the switch for all ?based Extreme switch products?
- Question #5
Which CLI command would you use to configure VLAN corporate with a tag value of 100?
- Question #6
In an Extreme switch, if MAC address learning is disabled on a port, no traffic destined to a permanent MAC address matching that port number will be forwarded, not even broadcast...
- Question #7
Broadcast frames are the only type of frames that may flood across VLANs.
- Question #8
What VLAN types are supported in ExtremeWare?
- Question #9
Which of the following CLI command line statements will configure an IP address on the default VLAN?
- Question #10
How would you stop a scheduled configuration download from happening? Use the CLI command:
- Question #11
An OSPF router type whose interfaces connect to two or more Autonomous Systems is called:
- Question #12
Which CLI command would you use to add a VLAN to a newly created STPD s1?
- Question #13
A newly-created VLAN has no member ports, is untagged, and uses protocol filter ny?until one configures it otherwise.
- Question #14
When the CLI command: show stpd, shows that the switch root bridge and bridge ID are the same, the switch is:
- Question #15
What command would you use to add a new SNMP read-write community string called u.nt.b9?on your switch?
- Question #16
Using RIP, how can you clear the IP routing table on a switch?
- Question #17
There are no collisions occurring on a stable full duplex Fast Ethernet connection.
- Question #18
When changing the password for John Doe management account, using the CLI command: config account johndoe password <cr>, you will be asked to enter the password twice.
- Question #19
In normal IP unicast routing, all forwarding decisions are based on the ______________ of each packet.
- Question #20
Which statement is true? In a PC, the configured default gateway:
- Question #21
If you wish to silently drop all traffic destined for IP network 100.219.10.0/24 with a gateway of 10.219.10.1/24 and without receiving any ICMP messages that would otherwise be ge...
- Question #22
How long in seconds, is the Extreme switch?FDB Aging time set at by default?
- Question #23
A Summit 7i switch can support up to __________ active Telnet sessions concurrently.
- Question #24
Which step would you take to configure a VLAN to only allow IP-related traffic?
- Question #25
Split Horizon and Poison Reverse are both enabled by default on an Extreme Switch after enabling RIP routing.
- Question #26
What load sharing algorithms are supported on switches with the ?chip-set.
- Question #27
What command would you execute to create a new protocol filter?
- Question #28
What is the result of enabling spanning tree in a network?
- Question #29
What is the proper CLI command syntax to create a user-level account for johndoe?
- Question #30
What is the default STP max age value?
- Question #31
How can you tell by looking at the front panel of an Summit 1i switch, which ports are disabled?
- Question #32
The following console speeds are supported when a switch runs in bootROM mode. (Choose the two that apply)
- Question #33
UDP, like TCP runs on top of IP networks but what differs UDP from TCP?
- Question #34
Which CLI command would you use to configure VLAN corporate with IP address 192.168.0.1/16?
- Question #35
How would you stop a scheduled configuration upload from happening? Use the CLI command:
- Question #36
STPDs s0, s1, and s2 have been created. What is the CLI command to enable spanning tree protocol for only s1?
- Question #37
The CLI console port utilizes a serial cable for physical switch to terminal connection.
- Question #38
The CLI command to prevent VLAN corporate from forwarding broadcast traffic for ports 2:2-2:6 is: config vlan corporate add ports 2:2-2:6 nobroadcast.
- Question #39
You need to change the name of a VLAN from corporate to corp. What steps would you take to do this?
- Question #40
When RIP is enabled in ExtremeWare, which RIP settings are than also enabled?
- Question #41
The ExtremeWare feature that configures the switch to copy all traffic associated with one or more ports for traffic analyses purpose is:
- Question #42
Which CLI command will configure VLAN corporate to use the protocol filter netbios:
- Question #43
What is the CLI command to configure a VLAN to only allow IPX-related traffic?
- Question #44
Which of the following CLI commands would you use to enable ECMP for RIP?
- Question #45
What is the well-known name for port 80?
- Question #46
What is the default area type for all OSPF areas created using the ExtremeWare CLI: create ospf area <area identifier>?
- Question #47
In an Extreme Switch, the routing function is disabled on all VLANs by default.
- Question #48
Which statement is true for an Ethernet bridge to perform its basic functionality?
- Question #49
The default settings for the console port of an ?chipset switch are: 9600 bps/8 data-bits/one stop- bit/no parity/software flow control
- Question #50
Link aggregation is supported on a Summit 1i and the following load sharing algorithm is recommended by Extreme Networks.