4A0-104 Exam Questions
298 real 4A0-104 exam questions with expert-verified answers and explanations. Page 2 of 6.
- Question #52
What is the minimum Ethernet physical network MTU required for a Layer 2 service on a GRE encapsulated SDP with a service MTU of 1514?
- Question #53
Which of the two following statements are TRUE?
- Question #54
The terms "customer" and "service" are used synonymously when describing a service implementation on the Alcatel-Lucent 7750 SR.
- Question #55
When configuring RSVP-TE for transport tunnels, which command enables RSVP by default?
- Question #56
A mesh SDP is used to create an Fpipe service.
- Question #57
Which of the following statements are FALSE regarding the VPN-IPv4 address family? (Choose 2)
- Question #58
Which of the following best describes how the path-mlu is chosen for an SDP?
- Question #59
Click on the exhibit button below. Assuming the customer only needs to monitor traffic from PE3 to the customer site, what two items are missing in the configuration of PE5, the Al...
- Question #60
Which of the following are characteristics of an IES service? (Choose 2)
- Question #61
Which of the following best describes an IES?
- Question #62
Which of the following commands is used to configure a new MPLS SDP?
- Question #63
A Cpipe supports both structured and unstructured frames.
- Question #64
Which of the following commands would be used to show the operational state of all IES services?
- Question #65
A network consists of 4 PE routers. A customer requires a VPLS service and has sites connected to each PE. Each site must have direct connectivity with all other sites. How many SD...
- Question #66
Which of the following best describes the label stack for a packet in the VPRN context?
- Question #67
Which of the following statements are TRUE about configuring a distributed Epipe service? (Choose 2)
- Question #68
Which of the following statements is FALSE about the VPN label?
- Question #70
A transport tunnel can either use an MPLS or GRE encapsulation.
- Question #71
Which of the following statements about VPRN is NOT true? (Choose 2)
- Question #72
In a Layer 2 encapsulation, using Martini, what does the first (top) label represent?
- Question #73
In a Layer 2 VPN service, the FCS is stripped when a customer packet arrives at the ingress PE and regenerated on egress.
- Question #74
Which of the following defines a SAP that will select frames with an outer tag of '4' and ignore any inner lag on a Q-in-Q encapsulated port?
- Question #75
Which of the following statements is TRUE regarding a VRF?
- Question #76
Service tunnels and transport tunnels are bidirectional and only require the operator to configure the tunnel on one router.
- Question #77
Which of the following best describes a VPRN?
- Question #78
A VPRN service is configured with BGP used as the CE-PE routing protocol. What address families are required on the PE-CE BGP session?
- Question #79
When a tagged packet is received on a SAP configured with dot1q encapsulation, the VLAN tag must match the value configured on the SAP in order to be forwarded.
- Question #80
When configuring an IES spoke termination to a VPLS, what must be explicitly configured in order for the service to come up? (Choose 2)
- Question #81
Which of the following SAP encapsulations support multiple services on a port? (Choose 3)
- Question #82
Which of the following statements is TRUE concerning route distinguishes on the 7750 SR?
- Question #83
Epipe services do no consume any MAC resources because MAC learning is disabled.
- Question #84
Which of the following best describes a VPWS?
- Question #85
An E-pipe is configured with a service MTU of 5000. What MTU value should be set on the access port for a Q-in-Q encapsulated SAP?
- Question #86
Choose the following components that are necessary for the configuration of a mirror service. (Choose 2)
- Question #87
What is the purpose of service mirroring on the Alcatel-Lucent Service Router?
- Question #88
Which of the following statements is TRUE regarding service mirroring?
- Question #89
A SAP configured in the form of 1/1/1:0/32 would be used for which type of VPWS?
- Question #90
By default, what happens when a packet with a VLAN tag is received on a SAP provisioned with null encapsulation?
- Question #91
Click the exhibit. E-pipe 100 is using an SDP with an LSP that uses the path shown (PE1-PE2-PE3-PE4). Based on the OAM command output, which of the following is FALSE?
- Question #92
Which protocol is used to signal the service label for a Layer 3 VPRN service?
- Question #93
A service needs to accept frames that have the following: an outer VLAN tag of 200 with an inner VLAN tag of 33; and frames that have an outer VLAN tag of 250 with an inner VLAN ta...
- Question #94
On a dot1Q encapsulated port, frames with a VLAN tag of 0 and untagged frames are forwarded to the null SAP
- Question #95
What is the best approach of making MTUs match between a VPLS and a spoke IES in order to bring up the service?
- Question #96
Which protocol is used to signal the inner label for a L2-VPN service?
- Question #97
Which of the following about the components of a service on the Alcatel-Lucent 7750 SR is FALSE?
- Question #98
Which of the following about the Alcatel-Lucent 7750 SR's sdp-ping utility is FALSE?
- Question #99
Which of the following can be used to detect the smallest path MTU in an RSVP signaled MPLS tunnel?
- Question #100
What is the minimum Ethernet physical network MTU required for a Layer 2 service on an MPLS encapsulated SDP with a service MTU of 1500?
- Question #101
Which of the following SAPs will toward tagged frames but NOT untagged frames?
- Question #102
Click the exhibit. PE1 and PE2 are Alcatel-Lucent 7750 SRs.What needs to be added to PE1's configuration to mirror traffic between PE2 and the customer site?