350-040 Exam Questions

What method is used to assign a pWWN to a dynamically assigned iSCSI initiator in a MDS?

What is the main purpose for Loop Initialization Protocol?

Host ports belonging to a VSAN which is moved to a suspended state will be:

On an MDS FibreChannel, QOS allows traffic to be prioritized in the fabric based upon:

When attaching to the following switch vendor, a VC_Ready flow control may have to be disabled and B2B Flow control enabled:

Before you can successfully enable the Call Home feature, which of the following must be true?

A customer has an existing production fabric with Brocade and McData FC switches intermixed. When adding an MDS 9000 switch, what MDS interop mode would be required? (Topology: McD...

Src-Id Dst-Id Ox-Id 0x0f0001 0x0fae12 1 0x0f0001 0x0fae13 2 0x0f0002 0x0cae12 1 0x0f0002 0x0cae13 2 0x0c0003 0x0cab12 1 0x0c0003 0x0cab12 2 The flows above are active within a 2 sw...

FC-SP is configured between two MDS switches. What happens if MDS_Switch_One's FC port is configured for "fc-sp auto-passive" mode and MDS_Switch_Two's FC port is also configured f...

When does a FCIP Interface need to be configured as B-Port?

You are connecting 2 independent and existing switches. Switch one has a domain ID of 1, Switch 2 has a domain ID of 2. An ISL is connected between the 2 switches. Both switches su...

In a scenario with three ISLs between two switches, a single host in VSAN 5 on switch A, and a single storage device on switch B in the same VSAN. What would be the effect on the I...

When a port channel that is trunking a given VSAN is quiesced, frames are lost. What can be inferred about this VSAN?

What selection below lists the architectural levels of the Fibre Channel protocol in order from the lowest level to highest level?

A switch boot failure can be caused by a corrupted image or corrupted bootflash file system. In the event of a corrupted bootflash filesystem which steps could be used to access BI...

What parameter does not need to be compatible for a port-channel to come up between 2 switches?

Changing the VSAN policy to "vsan policy deny" and then entering "no vsan policy" will have what effect on the role being configured?

The purpose of the SW_ILS ELP frame is to:

Select all of the primitive signals:

FCIP Write Acceleration most effectively addresses which disaster recovery challenge?

What conditions will trigger a port to perform the Link Initialization Protocol?

Which are possible ways to control access to targets on MDS with iSCSI proxy-initiator mode?

Which non-disruptive method should be used to view the PLOGI of a FC host to a FC target on the same MDS switch?

Which are required to be unique on a given MDS switch across multiple VSANs?

The committee responsible for the production and overseeing of Fibre Channel standards is:

Which conditions must exist for a FICON-enabled VSAN with a CUP device on an MDS 9509 switch, assuming that fibre channel zones are not used to control access to FICON-attached dev...

Click the Exhibit button. Each GigE interface on the MDS 9509-1 is peering with a corresponding GigE interface on the MDS 9509-2 via a point-to-point circuit on the optical ring. A...

What Fibre Channel transport functions can be found within the FC-2 level?

FCID 0x600000 is not a valid FCID in what interop mode?

The backup solution in which the least amount of impact is done to the database server is:

The function of "Boot Loader" during system startup is to?

What is the maximum number of FICON VSANs that can be configured on a 9509 switch?

Click the Exhibit button. The configured domain in VSAN 8 was changed from 0x30 to 0x97 and fcdomain was then restarted with the command, fcdomain restart disruptive vsan 8 . Vsan...

You have a legacy JBOD that uses copper DB-9 connecters. You want to connect your JBOD to a Fiber only Fibre Channel switch. You want to convert the DB-9 connection to multi mode F...

The committee responsible for the production and overseeing of SCSI I/O interface standards is:

A reason for persistent binding to be enabled on an HBA is to provide what benefit?

Which are required for a correctly configured iSCSI initiator to log into a MDS IPS Module?

What LUN is used when a host issues a SCSI CDB Report LUNs query to a target?

There are two 2 Gbps FC links formed into a single port channel connecting two switches together. What is the initial FSPF cost and resulting FSPF cost of the port channel if one o...

Select the true statements concerning the IP address subnetting requirements of gigabit Ethernet interfaces on the IPS-8 module:

What will happen to logged information if a MDS 9216 reboots?

You are asked to design a full-mesh core solution using the following equipment: 3 x 9509, fully loaded with 32 port FC modules (DS-X9032) 3 x 9506, fully loaded with 32 port FC mo...

In a DH-CHAP enabled port, what is required of a host before it can access the port? Cisco 350-040 Exam

Assume you have a class 3 connection. A switch port interface has 12 buffer credits. If a host with 24 buffer credits logs into this port, how many buffer credits will be made avai...

In the above picture, Switch 3 and Switch 5 are not IVR capable switches. All the ISLs are 1 GB links. Switches 2,4,and 6 are IVR-capable switches. What is the FSPF costs from Swit...

During an E-Port initialization, what internal link service is used to exchange Link Parameters and the operating environment of the two interconnecting ports as well as the capabi...

An FCIP profile can be shared by how many FCIP interfaces?

You currently have 1 host and 2 target devices grouped into the same zone. The zone is part of the active zoneset. When one of the target ports was removed from the switch, the hos...

Which two features would best improve "write" performance on a single FCIP tunnel over a 10 Mbps WAN with high delay?

What statement regarding LUN zoning is accurate?