200-601 Exam Questions

Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection and sets the priority value that would break the tie between switches with matching...

What are three Cisco best practices for running I/O control traffic in a wireless environment? (Choose three)

If the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE wi...

Refer to the exhibit. Which lines represent an I/O connection running at a 20ms RPI?

Which describes the relationship between a workgroup bridge?

Which best describes the difference between 802.11n and 802.11ac?

Refer to the exhbit. Which three elements would enable high availability and predictable performance for a motion control application spread across two switches (with video and I/O...

Refer to the exhibit. Which values are correct for AP 2 to allow for efficient roaming?

Which two actions are examples of network device hardening for Cisco Industrial Ethernet Switches? (Choose two)

You are called at home at 3am by an unskilled machine operator with a suspected network related problem; the controller LEDs are all normal but the output module's communications L...

Which three network mechanisms can be used for securely segmenting an industrial network? (Choose three)

Your controller has a high performance EtherNet/IP interface with port speed of >30,000 packets per second and 80% spare capacity. A new PowerFlex 753 drive will be added to the sy...

A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104. Both standard controll...

Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion?

You have reached the limit of IPv4 IGMP groups available on a Cisco IE 3000 switch that was deployed using the Express Setup. Which CLI command will increase the number of availabl...

Refer to the exhibit. A new device, PanelView, has been added to the network. See the table for device details: All devices are able to ping their default gateway and all other dev...

To correctly integrate a Cisco Industrial Ethernet switch into a ProfiNET management system such as SIMATIC STEP 7 or TIA Portal, which is a mandatory action?

Refer to the exhibit. The control system depicted in the exhibit uses VLAN 300 for all of its device ports and PVST is enabled on each switch to switch connection. L2SW4 was insert...

Which statement is correct regarding ProfiNET communication classes?

A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet switch that has been added to a SIMATIC management station. Based on t...

What can be done to increase the security in depth in an industrial zone?

Your supervisor calls you and tells you that one of the Stratix 5700 switches is not assigning all CIP explicit messages to the proper QoS queue. The switch was deployed with the a...

What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables?

Cisco Industrial Ethernet switches are capable of sending alarm messages to ProfiNET management stations using the ProfiNET-IO protocol. Which four are alarms that can be configure...

Which five are characteristics that describe Cisco Industrial switches? (Choose five)

Refer to the exhibit. The Robot Cell is in a bottling plant. This cell environment needs to consider high flex, EMI, and possible exposure to moisture. Which physical media compone...

What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data?

Refer to the exhibit. All of the vlans listed in the routing table below are trunked using 802.1q and are active on all switches. PLC1, PLC2, and PLC3 each has IP address 192.168.0...

Refer to the exhibit. Which two parameters can be used to diagnose an overloaded system? (Choose two)

Which CLI command will display IGMP snooping information in a Cisco IE2000 or Stratix 5700 switch?

Refer to the exhibit. Which lines represent a CIP connection being established between two devices?

What is the reason that ProfiNET frames are discarded by default on Catalyst switches?

What security component can be deployed to increase the defense in depth and specifically can be positioned against 'man-in-the-middle' attack?

Given the CIA triad elements, which ensures first that the data is encrypted and secure, second that the data is trustworthy, and third that the data is accessible by those who nee...

To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?

Refer to the exhibit. CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to outpu...

Refer to exhibit. The administrator has configured the following device IP settings, but did not keep track of which ports the devices were connected to. The administrator is able...

A shutdown in the cookie cutter machine was traced to a broken network cable. What are two reasons that explain why using DLR is an appropriate choice for network resiliency? (Choo...

Which characteristic causes multimode fiber-optic cable to differ from single mode?

Which command globally enables QoS on a Cisco Industrial Ethernet switch?

You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on-line with RSLogix5000. When do the changes you have made get published to the sw...

Refer to the exhibit. SW1, SW2 and virtual switch are connected in a loop. SW1 and SW2 are standard layer-2 switches. Which loop prevention mechanism is best suited for use within...

Refer to the exhibit. NAT has been configured on the router 'GW' and the IP addresses of router 'GW' have been configured properly. Users of PC1 and PC2 are able to ping the IP add...

It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are...

In which two ways could you minimize the impact of monitoring an industrial network? (Choose two.)

Which option best describes the ProfiNET Discovery and Configuration Protocol (DCP)?

When troubleshooting a high packet loss condition in the network, the inspection area has an assessed M.I.C.E. value of M=1, I=1, C=3 and E=1. Which condition could be suspect?

Refer to the exhibit. You are required to implement traffic segmentation in the network. See the table for relevant device details: L2SW4, L2SW5, and L2SW6 are connected to L3SW1 w...

You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristi...

ProfiNET has been disabled on a Cisco Industrial Ethernet switch. Which CLI command will correctly enable ProfiNET on the switch?