150-230 Exam Questions
206 real 150-230 exam questions with expert-verified answers and explanations. Page 2 of 5.
- Question #51
Two sites 8 km apart will be connected together using fiber optic cable. Which SFP/cable combination needs to be used?
- Question #52
A powered device connected to a Brocade FastIron device has been auto discovered and classified as a class-3 PoE device. However, its power consumption is only 10 watts. Which comm...
- Question #53
Which two Layer 2 network discovery protocols are used to detect PoE power requirements? (Choose two.)
- Question #54
Referring to the exhibit, which route will be installed in the IP routing table?
- Question #55
Referring to the exhibit, which route will be installed in the IP routing table?
- Question #56
You need to route a specific block of addresses through a specific destination. Which Brocade protocol-independent feature would you use?
- Question #57
Your network is connected to two ISPs, ISP1 and ISP2. Since ISP1 is more costly then ISP2 you would like to route all incoming traffic to go through ISP2. Which change would you ma...
- Question #58
Your Brocade device has two connections to your ISPs and you want to load balance your BGP traffic across the links to ISP1. Which Brocade routing feature allows this?
- Question #59
Your company wants to merge an old RIP network to the corporate OPSF network. When configuring your ASBR which three actions would you use to integrate the routes in each network?...
- Question #60
Your network is connected to two ISPs. ISP1 is more expensive than ISP2. You would like to route all outgoing traffic to ISP2. Which BGP attribute would be modified to implement th...
- Question #61
Which multicast prefix is correct for IPv6?
- Question #62
When IPv6 is configured on a Brocade switch, what is the throughput rate compared to IPv4?
- Question #63
An IPv6 address is composed of how many fields of 16-bit hexadecimal values?
- Question #64
What are three PIM SM device types? (Choose three.)
- Question #65
What are two required tasks to configure a Brocade Layer 3 switch for PIM Sparse mode? (Choose two.)
- Question #66
How many IPv4 multicast groups use the same Ethernet destination MAC address?
- Question #67
Which bits of an IPv4 multicast address are mapped to bits of a MAC address?
- Question #68
Referring to the exhibit, where would you enable IGMP snooping?
- Question #69
A client has been monitoring the network and has observed excessive multicast traffic on many of the subnets on the PIM-DM enabled network. Why would changing to PIM Sparse mode re...
- Question #70
You upgrade a network from STP to RSTP to improve the reconvergence time. When a link or port in the network fails, the network reconvergence is improved. However, the reconvergenc...
- Question #71
Users often make the mistake of connecting devices to your network without telling you. You want to prevent spanning tree participation between your network and user devices. Which...
- Question #72
You are running 120 VLANs across your Brocade MLXe network. Each VLAN has its own spanning tree instance. There is a need to double the number of VLANs on the network. Which two ac...
- Question #73
You are about to add links to your Spanning Tree Protocol (STP) network. Some switches will have multiple links to adjacent switches. You expect STP to manage the topology. Which t...
- Question #74
You are managing a spanning tree network. A user connects a small switch to a network port causing the network to briefly go down; now all the applications run slow. Which feature...
- Question #75
You are managing a spanning tree network. A user connects a small switch into a network port causing the network to briefly go down; now all the applications run slow. What took pl...
- Question #76
You notice that the Spanning Tree Protocol (STP) has selected a root bridge at the edge that is not ideal for the physical network topology. You would prefer that the root bridge b...
- Question #77
Your upcoming expansion plan requires more VLANs. Your switch infrastructure will not support enough STP instances to permit one per VLAN in the new design. Which technology will r...
- Question #78
You would like to install additional Layer 2 inter-switch links in your network to add bandwidth and increase redundancy. However, you know that the default settings on your switch...
- Question #79
You experience spanning tree stability problems with RSTP in your network. Which technology will remedy the situation?
- Question #80
You have successfully configured a VLAN group on your Brocade FastIron switch. Which statement is true?
- Question #81
Your customer is deploying several small switch stacks around a city in a resilient ring. You decide to implement topology groups to aid in VLAN management. Which two statements ar...
- Question #82
You want to provide Layer 2 and Layer 3 resiliency in your network. Which two statements are true? (Choose two.)
- Question #83
You are building a ring topology around multiple buildings and want to deploy a standards-based resilient topology. Which two statements are true? (Choose two.)
- Question #84
You have many VLANs configured on your Brocade device. You want the features of Rapid Spanning Tree Protocol (RSTP), but have more VLANs than available RSTP instances. Which protoc...
- Question #85
Referring to exhibit, you have connected an MCT unaware switch to Brocade MLXe MCT peers. The VRRP-E master routes traffic to the MCT unaware switch. Which two statements are true?...
- Question #86
In a VRRP master selection, which router will become master and what will the master default priority become?
- Question #87
Referring to the exhibit, if e 3/2 goes down, what will happen?
- Question #88
In VRRP-E how are hello packets sent?
- Question #89
Referring to the exhibit, if port e 14 were to go down on Router A, how would this affect VRID 1?
- Question #90
In the exhibit, you have a router that has two connections to another router. You want to load balance across BGP interfaces. Which BGP routing configuration step is required?
- Question #91
Referring to the configuration shown in the exhibit, which three networks will be advertised to BGP peer 10.255.17.98? (Choose three.)
- Question #92
You need to simulate the join of several hosts on a subnet. How would you configure your Brocade MLXe?
- Question #93
You need to configure multicast snooping on a Brocade MLXe. Which element will support this function?
- Question #94
In VRRP-E, which two statements are true? (Choose two.)
- Question #95
In VRRP-E, which two statements are true about the use of the non-preempt-mode setting? (Choose two.)
- Question #96
In a VRRP-E, which statement is true about the use of the command slow-start 10?
- Question #97
Referring to the exhibit, if port e 14 were to go down on Router A, how would this affect VRID 1?
- Question #98
Referring to the exhibit, if e 2/4 goes down, what will happen?
- Question #99
Referring to the exhibit, if Virtual Server1 is dynamically moved to Host Server2 which path will the packets take?
- Question #100
Referring to the exhibit, if Virtual Server1 is dynamically moved to Host Server2 which path will the packets take to reach remote clients?