150-230 Exam Questions

Which router sends network LSAs?

Which LSA is generated when an area only requires a gateway to routes outside the autonomous system?

Referring to the exhibit, which two routers would be ASBRs? (Choose two.)

Which LSA lists all local active OSPF links and their associated costs?

Your company is connected to an external network and is receiving an external prefix. Which LSA type will be sent from the external network?

You want to rate limit all Layer 2 traffic with a priority level of 3. Which action would you perform?

You need to rate limit the traffic on a port to a guaranteed rate and allow small bursts. Any traffic that exceeds these limits must be set to the lowest priority level. Which acti...

You have set up a dynamic LAG with four ports. Now you want to apply TOS-based QoS. Which two statements apply? (Choose two.)

You are configuring QoS in your network. What are two purposes of the Excess Information Rate (EIR)? (Choose two.)

You are configuring QoS in your network. What are two purposes of the Committed Information Rate (CIR)? (Choose two.)

You are configuring the network for an application that requires QoS at Layer 2. Which QoS field in the header should be used?

Ethernet frames containing 802.1p values and IP packets containing TOS values ingress on a Brocade router. Which QoS value will be used?

You are implementing QoS on your network. How many queue values are there?

An IP phone has set a DSCP priority. It has been honored through a Brocade FastIron switch and has arrived on the interface of a Brocade MLXe router. You want the MLXe to honor the...

You are configuring a network for an application that requires QoS, based on the IPv4 header. Which QoS field in the header should be used?

You have traffic classified in your switch to use priority 7. You decide to enable stacking on the switch. Your traffic is no longer being queued in priority 7. Which two events ha...

The ingress port on a switch receives a packet marked with DSCP 45. You want it to have DSCP 47 when it leaves the switch on the egress of the uplink. Which method would accomplish...

Your IP phone sends a DSCP value of 47. You want the value to be placed in 802.1p queue 5 on a Brocade FastIron FCX. Which statement is correct?

You want your Brocade FastIron switch to recognize DSCP, TOS, 802.1p, and IP precedence bits from an IP phone. What must you do first to ensure the QoS parameters are recognized by...

When configuring QoS, in which two ways will priority be forced? (Choose two.)

You are deploying security methods to allow authorized IP addresses to access your network. Which two statements are true? (Choose two.)

You have a customer who wants to separate their user's traffic based on credentials. Which two steps are required within the appropriate devices to achieve this goal? (Choose two.)

Your security department requests that you enable access to a secure resource on a per-user basis. These users can log in from multiple devices on the network. Which two actions sh...

You want to restrict access to the management functions of your Brocade devices using an IP ACL. Which two access methods can be restricted? (Choose two.)

Your company is developing applications and wants to limit traffic to its development teams. The applications should work with both IPv4 and IPv6. Which two statements are true whe...

You are configuring IPv6 ACLs. What are two implicit results? (Choose two.)

You are deploying 802.1x authentication to all your company's devices and edge switches. A visitor connects their non-802.1x enabled device to your network. What will happen?

Your customer wants you to configure a user on VLAN 200 and enable MAC port security on VLAN 200. You are only to enable port security on interface e 1 to interface e 14. What will...

You are using 802.1x and want unauthorized users to be placed in a VLAN outside of the firewall in a DMZ area. What should you do?

You have configured the multi-device port authentication feature on a switch to authenticate MAC addresses using RADIUS. Now you want the authenticated MAC address to use dynamic V...

You have configured two routers for OSPF with area 0 configured on the correct Ethernet interfaces. On each router, you see that the OSPF neighbor state is in INIT state. What are...

You have configured a new router's OSPF priority to become the designated router for one of its directly connected networks. Two other routers in the same network have already been...

You have installed a new router. However, you cannot establish an adjacency with the upstream router. Which two conditions will prevent adjacency? (Choose two.)

Two OSPF neighbor routers are unable to establish an adjacency. Which two conditions would cause this issue? (Choose two.)

Neighbors on a given OSPF network will go through six states on their way to fully becoming synchronized with their routing tables. What is the proper sequence of the last three st...

Neighbors on a given OSPF network will go through six states on their way to fully becoming synchronized with their routing tables. What is the proper sequence of the first three s...

Hello packets are being transmitted by an OSPF router. Which IPv4 multicast address is used?

In an OSPF network, you want to ensure that a router does not participate in the DR election process. How would you do this?

You need to configure OSPF adjacency on a router. Which three actions are required? (Choose three.)

You need to eliminate the need for an OSPF DR router. Which topology would be used?

An OSPF router is going through the OSPF adjacency process. Which step in this process does the router first perform in the DR/BDR election process?

Through which OSPF adjacency state does the router describe its entire link-state database?

You have a router that you want to become an OSPF DR. All routers in the area are currently set at the default values. How would you ensure that the router becomes the DR?

You have added an OSPF router to your network and it remains in a Down state. Which statement is true?

You show OSPF router A to be in a 2-Way state and router B and C OSPF routers in a Full state. What does this mean about router A?

Which type of OSPF LSA is used to advertise routes into a different area?

Click the Exhibit button. Brocade#sho ip ospf database link-state router Area ID Type LS ID Adv Rtr Seq(Hex) Age Cksum 0 Rtr 10.100.1.6 10.100.1.6 80000004 641 0x2d01 LSA Header: o...

You have been asked to configure a new EBGP connection to your service provider by peering using your loopback address. Which two steps must be taken to ensure proper EBGP peering?...

Which three transceiver form factors are supported by Brocade switches and routers? (Choose three.)

Which type of transceiver would be used to support a 5 km single mode fiber 10 Gbps connection?