150-230 Exam Questions

Referring to the exhibit, which router will become the VRRP-E master?

Referring to the exhibit, you have connected an MCT unaware switch to Brocade MLXe MCT peers. The VRRP-E master is routing traffic to the MCT unaware switch. Which three statements...

There are two Brocade MLXe MCT peers in your network. Client #1 is operating in strict-mode. CCP fails. Which statement is correct?

Referring to the exhibit, there are two Brocade MCT peers. Multiple VLANs are configured between the two peers and the MCT client. Which statement is correct?

You connect MCT Client #1 to two Brocade MLXe MCT peers. The ICL link between the MLXe nodes fails. The keepalive VLAN maintains communication between MLXe nodes. Which two stateme...

You have just implemented MCT in your Brocade MLXe network. Which three statements are true? (Choose three.)

Referring to the exhibit, what is the proper configuration on Router A to send all input and output traffic from Ethernet interface 4/1 to the collector?

A LAG between two Brocade MLXe routers bounces. Some of the ports remain in an LACP blocked state. Referring to the exhibit, what must you do to remedy the situation?

You must provide a network monitoring solution for an IP network that includes three criteria: device discovery, sampling of data, and SNMP trap selection. Which Brocade monitoring...

When sFlow is enabled on a Brocade FastIron switch, the system performs which three sFlow- related tasks? (Choose three.)

You need to implement an IP network solution to manage IP switches and routers that includes call home and e-mail notification. Which solution will satisfy the requirements?

You made some network changes on one of your Brocade FastIron switches and you lost the link to several small mini-switches on the office floor. You execute a show interfaces brief...

On your Brocade MLXe, you experience a large number of BGP routes being advertised and withdrawn from your downstream ISP. You need to prevent this from constantly happening. Which...

You have configured Rapid Spanning Tree (802.1w) on your VLANs. You notice delays of 30 seconds or more before workstation and server ports start to send and receive traffic after...

You have deployed Brocade FastIrons for several years in a Power over Ethernet (PoE) implementation. You computed the power budget for each switch, and determined that there would...

Your installers have installed IP phones on your Brocade FCX HPOE switch. You use show inline power and notice that there are 802.3at devices in the table. Why should you be concer...

Referring to the exhibit, what must you do to make the LAG function on a Brocade NetIron MLXe?

You have two routers: R1 and R2, running BGP. R1 is peered to ISP1, R2 is peered to ISP2. You want outbound traffic to use ISP1 and only use ISP2 as a backup. You have created a ro...

You have an existing network of Brocade MLXes running OSPF between them. You have recently added 10 Gbps line cards and have connected them between some of the routers, but you hav...

You have decided to add a second link between your existing Brocade MLXe running BGP and your service provider. What are three configuration changes you will need to make in your B...

During a BGP neighboring session, a Brocade router remains in the active state. What are two explanations for this? (Choose two.)

Routers on the network are not seeing the ASBR default route. Which statement is correct?

You install a router configured to run OSPF. You issue show ip ospf neighbor and notice that the neighbor list is empty. What are two explanations for this? (Choose two.)

You attempt to build an OSPF virtual link between two ABR routers and it fails to form. What are three explanations for this? (Choose three.)

You have changed the outbound policy on a BGP router. What must you do to apply the changes?

You install a router configured to run OSPF. You issue show ip ospf neighbor and notice that the neighbor remains in the INIT state. What would explain this?

You have a Brocade IronStack of four FCX units actively running with sequential unit IDs. You need to replace unit ID 3 with a new unit. Which two statements are true? (Choose two....

You have installed a new 2 x 100 GbE interface module into a Brocade MLXe. The first port is functional, however, the second port on the module is not functional. What would cause...

After hot swapping an interface module (LP) on a Brocade MLXe, the interface module boots up to an interactive state, instead of an active state. What is causing this?

You are performing a management module switchover or hitless upgrade on a Brocade MLXe router. Which two statements are true? (Choose two.)

You are performing a management module switchover or hitless upgrade on a Brocade MLXe. Which two statements are true? (Choose two.)

You are adding a Brocade FastIron ICX member to a Brocade ICX IronStack. Which two statements are true? (Choose two.)

Three Brocade FCX switches are configured as an IronStack switch. The active controller fails. Users connected to the IronStack lose connectivity for over 70 seconds. What would ca...

You need to increase the maximum amount of VLANs that a Brocade FastIron switch allows by default. What is the correct procedure?

You have decided to replace a four-port 10 GbE line card in your Brocade MLXe with an eight- port 10 GbE line card. After performing the hardware swap, the new card will not enable...

You have turned off IPv4 management on your Brocade MLXe and must now use IPv6 management. Which two tasks will the IPv6 ncopy command do? (Choose two.)

You want to enable OSPF graceful restart on your Brocade router. What are two ways to configure this? (Choose two.)

You are currently using SNMPv2C to manage your network. Your management wants you to set up a more secure user-based security model. You will be implementing SNMPv3 as a solution....

On your sFlow collector, you notice that the source address from your Brocade MLXe router is not what you expected. What is the first address that sFlow will use as a source addres...

You want to mirror the tagged VLAN traffic from Router A to the collector, but the mirrored traffic must go through Router B to reach the collector. Referring to the exhibit, which...

You notice a high amount of packet fragmentation messages on the router. What would cause this?

You work on a large distributed network that includes 30 Brocade MLXe series routers. One of your MLXe routers has logged a series of TCN notifications. What are two results? (Choo...

You discover that the Brocade FastIron has increased CPU utilization. What are two explanations for this? (Choose two.)

You have configured a BGP router to communicate to a peer from a specific loopback. During implementation, you discover you are not peering. What would cause this?

Your network has gone through a security overview and hardening. Your BGP router has now lost connectivity. What is causing this to happen?

You are configuring a router for use as an OSPF ABR router. When configured, you issue the show ip ospf neighbor command. You notice that the router remains in EXSTART. Which state...

The root bridge router has issued a series of TCN BPDU notifications. Which two conditions would you look for on the network? (Choose two.)

In the exhibit, you deployed a pair of new Brocade MLXes for your server farm interconnects using MCT with jumbo frames. After you deployed the new switches, you establish adjacenc...

You install a new Brocade SX router on a network. You configure each VLAN to run RSTP. One VLAN has reverted to STP. What has occurred?

You have been asked to configure a new EBGP connection to your service provider. You know that the service provider's keepalive and holdtime settings are manually set but you do no...