NS0-502 Exam Questions

After completing the configuration of a new Brocade Fibre Channel switch, which command do you use to verify your configuration?

Which native GUI switch tool is used to manage Cisco MDS-Series switches and directors?

Which configuration for primary block (FC and iSCSI) data does NetApp best practices recommend? (Choose two.)

When running diagnostic tests after an initial installation of a NetApp FAS3000 storage system, which command is used to run a comprehensive set of diagnostic tests on the entire s...

You are about to replace a failed Brocade Fibre Channel switch. Which three steps do you take prior to connecting the switch in the SAN? (Choose three.)

At which storage object level is deduplication enabled?

Which commands allow you to enable NetApp deduplication and verify space savings?

Which row of items should you look up in the IMT (Interoperability Matrix Tool) when designing a NetApp Storage Solution for a customer?

Which option needs to be set on a volume to guarantee that it cannot be affected by other volumes?

Which option needs to be set on a LUN to guarantee that it cannot be affected by other LUNs in the volume?

When does Fractional Reservation reserve space from the volume?

Click the Exhibit button. In the diagram shown, a portset is created on controller 1 with the command: controller1>portset create -f ntapportset 0b. This portset is bound to the ig...

What are three relevant perfstat counters to check for unaligned I/O that do not fall on the WAFL boundary? (Choose three.)

Click the Exhibit Button. The table highlights the space management policy that is defined for a particular flexvol, acmevol. Based on the information provided in the table, which...

Which utility on Windows 2003 and Windows 2008 can be used to collect information about firmware and driver versions for an Emulex LP1xxxx/LPe1xxx HBA?

Which utility on Solaris 10 can be used to collect information about firmware and driver versions for an Emulex LP1xxxx/LPe1xxxx HBA?

Which utility on Solaris 10 can be used to collect information about firmware and driver versions for a Qlogic QLAxxx/QLExxxx HBA?

An organization currently has a NetApp Fibre Channel block-based solution. With limited budget and resources, they want to create a new disaster recovery site that utilizes a NetAp...

A company has a Fibre Channel environment and wants to connect a new host in a remote data center using 50/125um OM2 multi-mode fiber cable and needs to support 2 Gb speeds. What i...

Zoning by World Wide Port Name (WWPN) is deployed and a host HBA is replaced. Which zone change needs to be made?

Which three protocols can be used for communications between a host running SnapDrive for Windows and the NetApp Storage Controllers? (Choose three.)

Any newly installed system with Data ONTAP 7.3.1 supports which cfmode?

A company has deployed a NetApp dual controller FAS3100 series with iSCSI. Currently, there are five Windows servers and three Novell NetWare servers connected to the IP SAN. The c...

Which native GUI switch tool is used to manage Brocade switches and directors?

Which command will display which Brocade switches are connected into a fabric?

Which command collects detailed diagnostic information from a Brocade FC switch?

Which command on a NetApp storage controller will display the average latency time on a per LUN basis every five seconds?

Which command on a NetApp storage controller will display the average service time on a FC target port basis every five seconds?

A company has five Windows servers that are dual-attached, four Linux servers that are single- attached, and ten dual-attached Solaris servers. The company wants a highly available...

In Data ONTAP 7.3, what is a portset bound to?

A dual controller FAS3100 series is connected to a dual fabric with two active target ports per fabric in a single-image cfmode, and uses a single portset. What is the number of pa...

What are two performance tuning parameters available for Fibre Channel HBAs on a host? (Choose two.)

You connect a host to a NetApp storage system through an FC switch. The host has its boot volumes on the NetApp storage system. What is mandatory for you to configure?

A Solaris administrator just noticed that a host has lost connectivity to the company SAN. Which file should the administrator check for SAN connectivity errors?

Which NetApp host utility command determines the number of paths per LUN visible to the host?

You have a Windows 2003 host using the NetApp ONTAP DSM MPIO environment with a FAS6000 high availability configuration running single image cfmode. When you disconnect a cable fro...

Click the Exhibit button. A Solaris 10 host with VERITAS Storage Foundation 4.1 is FCP attached to a FAS3140 high availability storage system running single image cfmode. Using the...

Which host-based tool will enable you to stripe a LUN across multiple NetApp controllers?

What are two possible impacts to consider when changing the cfmode to single_image?. (Choose two.)

What are two functions of iSCSI access lists? (Choose two.)

What is the significance of using a specific LUN type when creating LUNs manually on a NetApp storage system?

Which three tasks can SnapDrive perform? (Choose three.)

When planning for fault tolerant power connections, how should each device to be connected?

Which statement is correct regarding virtual machine alignment on VMware ESX?

Which of these attributes can affect LUN I/) alignment?

Which statement is NOT true regarding NetApp Snapshots of VMware ESX datastores?

Which statement correctly describes ALUA concepts on NetApp Storage solutions?

On ESX 4.0 for guest operating systems in a Microsoft cluster configuration, the Path Selection Plug- in (PSP) for a MSCS LUN should be set to:

A user wants to access a FCP VMFS datastore created on a NetApp LUN using a properly configured ESX 3.5 system with a new ESX 4.0 system. Without making changes to the LUN or igrou...

Which three steps are required to make a LUN visible to a NPIV-supported VM? (Choose three.)