NS0-181 Exam Questions

A customer wants to reduce the disk allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The...

A customer has a new 2-node ONTAP system. They have configured the cluster for iSCSI and LUN access. Which two statements are correct in this scenario? (Choose two.)

Starting with ONTAP 9.1, what is the maximum number of HA pairs that are supported when using a SAN cluster?

What is a valid failover policy for a SAN LIF?

You are adding two new nodes into an existing switchless 2-node cluster. Which two statements are true in this scenario? (Choose two.)

Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.1 system. The customer req...

Click the Exhibit button. Please choose one of the following: (1) Normal Boot. (2) Boot without /etc/rc. (3) Change password. (4) Clean configuration and initialize all disks. (5)...

You Install a new 2-node FAS8200 switchless cluster. You want to reach all necessary management LIFs and SPs for this cluster. How many management IP addresses do you need in this...

Click the Exhibit button. After running Config Advisor 5.0 on a newly deployed ONTAP system, you are reviewing the output with the customer, and you find the warnings shown in the...

In which two configurations would Advance Drive Partitioning be used by default in ONTAP 9.1? (Choose two.)

What is the main function of ACP?

After the Installation of a new 2-node cluster, you want to make sure that AutoSupport is working as expected from the cluster. In this scenario, what are two ways to trigger a new...

To ensure that your customer's cluster is robust and operational, you need to be familiar with configuration best practices. Which three practice rules should you always follow? (C...

Config Advisor reports that you have a single point of failure on a stack of shelves. After investigation, you have assigned the following ports to each stack: stack 1 -ports 0a an...

You want to expand an existing FAS8060 switchless cluster running ONTAP 9.1 with an AFF A300 System. Which action should you take to perform this task?

A customer has a stack of shelves with both DS4243 shelves and DS4246 shelves. The customer wants to replace the DS4243 shelves with new DS4246 shelves. What would you advise the c...

Without adding new cluster interconnect switches, you want to nondisruptlvely upgrade from FAS2554 controllers to FAS8200 controllers on an existing 2-node switchless cluster runni...

Select the Exhibit tab. You finished the Installation of a new FAS8200 system. The customer wants to use FC and 10G Ethernet but only has the onboard UTA2 ports available. Referrin...

switches. The current workload runs NAS protocols. A business unit wants to add an additional workload that requires expanding the cluster by six AFF A300 nodes and use SAN protoco...

You have just installed a new FAS2650 HA for your customer. You are now configuring the AutoSupport transport section. In this scenario, what Is the NetApp best practice for this t...

You are going to add a node to an existing cluster but first you must gather the appropriate Information for the new node's management UF. What two pieces of Information is require...

You just finished an AFF A300 installation with two DS224C disk shelves. What are two ways to cable these disk shelves? (Choose two.)

You finished the Installation of a 2-node cluster and want to determine correctly. What are two ways to accomplish this task? (Choose two.)

After an Installation, your customer asks you if you have a solution or a product that can easily list all the elements of a running ONTAP cluster, and highlight the changed and ne...

You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs. Which statement...

A customer has a standard request for information regarding the installation, configuration, usage, and maintenance of this NetAPP equipment. What is the appropriate priority level...

After completing an installation, the customer wants to know they can manually open a new technical case with NetAPP Global support. What are three ways to accomplish this task? (C...

You finished an ONJAP 9.1 Installation using the Information provided by the customer, but the NFS exports and CIFS shares cannot be accessed using the newly created data UFs. In t...

You have created an aggregate with one RAID group on your ONTAP 9 cluster. Two disks have already failed and have not finished reconstructing.

You have just replaced a FAS controller with a new controller and Installed the appropriate licenses for the new FAS controller. What are two ways to remove unused licenses In this...

You are asked to Install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf. Which shelf would you add to th...

What are two ways to obtain customer licenses for a new ONTAP system? (Choose two.)

You were dispatched to add a OS224C to an existing HA pair that has a stack of DS4243 shelves with 1 TB drives and a stack of DS4246 shaves with l TB drives. The customer wants to...

You Install a new AFF A300 2-node switchless cluster with ONTAP 9.1 at a customer site. Each node a root aggregate as part of the system configuration. In this scenario, what is th...

Your customer has a new FAS2650 HA cluster with ONTAP 9.1 Installed. The cluster Is connected to two - N1610 switches. Which two statements describe this Installation? (Choose two....

You are configuring a new system with ONTAP 9.1. You created interface groups, VLANs, and a broadcast domain for the new ports on all the nodes of your cluster. During the configur...

Which two default broadcast domain does the system create during initialization? (Choose two.)

Which is the minimum number of ISCSI LIFs Per node in ONTAP 9.1?

Select the Exhibit tab. Your customer has an AFF A300 Installed, They ask you to configure the e0a and e0b ports to use the FC protocol.

You are setting up a new cluster. The customer notices that there are many management ports on the cluster. The customer wants to know the purpose of the cluster management LIF. In...

You have a 2-node switchless cluster in a remote location. Node 1 has taken over node 2. You want to access node 2 to investigate the problem. In this scenario, how would you conta...

Select the Exhibit tab. The exhibit illustrates the network cabling of a 4 node HA duster that includes four separate networks. Which two definitions are correct in this scenario?...

Select the Exhibit tab. What is the cause of this error?

Select the Exhibit tab. You install a new FAS2552 HA using a DS2246 disk shelf and ONTAP 9.1 on a customer site. Referring to the exhibit, Which two statements describe what is req...

A customer ordered two new DS224C shelves.The Customer wants you to add these shelves to an Which statement is true in this scenario?

A customer buys a new switchless ONTAP 9.1 FAS2650 cluster. You are asked to install the system at the customer's site. Which three steps are needed to accomplish this task? (Choos...

You are asked to install a new ONTAP cluster at a customer site. In this scenario, which ONTAP versions would you normally install? (Choose two.)

You have just added a new DS4246 shelf with 24 x 10 TB SATA HDDs to a single FAS2650 node as the first SATA shelf. You must keep two SATA spare disks on the shelf. What Is the maxi...

Which tool would help you to verify an installation of an ONTAP cluster?

You are asked to install a 2-node FAS2554 cluster running ONTAP 9.1. The controller arrived with ONTAP 9.0 Installed. In this scenario, which two tools would be used to complete th...