NS0-180 Exam Questions
69 real NS0-180 exam questions with expert-verified answers and explanations. Page 1 of 2.
- Question #1
What is the next step if you must escalate an open case?
- Question #2
You want to install a new clustered Data ONTAP 8.3 system with a FA8080. The customer has unused licenses available from a clustered Data ONTAP 8.1 system. What should be considere...
- Question #3
After proper cabling the NetApp CN1610 cluster switches, you notice that joining the second node to a cluster fails because the node is not able to communicate with the other node....
- Question #4
You will be performing a new cluster Data ONTAP 8.3 or later installation. Which three tools would you download to facilitate this task? (Choose three.)
- Question #5
Click the Exhibit button. Customer wants to modify the properties of their SPI Web services as shown in the exhibit. What is the reason for the error?
- Question #6
You are asked to install a cluster that consists of two FAS8060 controllers and four DS2246 shelves. The customer wants two stacks of shelves (10-11 and 20-21). According to NetApp...
- Question #7
What is a protocol?
- Question #8
According to NetApp best practices, which two sets of protocols would be assigned to the same storage virtual machine (SVM)?
- Question #9
You are verifying multipathing from the host to the storage controller. Which three components should you verify? (Choose three.)
- Question #10
You are planning to move to a newer clustered Data ONTAP version. Which two resources should you review prior to the move? (Choose two.)
- Question #11
A customer learns that a certain NetApp tool allows remote data collection, intelligent core file handling, and notification of down storage controllers for technical support analy...
- Question #12
While testing storage failover, you receive an error message indicating that you have a disk inventory mismatch. What is a reason for the error message?
- Question #13
What are two supported cluster interconnect switches for the FAS8040 nodes? (Choose two.)
- Question #14
Which technology allows NetApp to ship replacements for defective parts automatically?
- Question #15
A customer is installing a new system. The administrator needs to have the maximum available amount of data space. Which disk configuration should the administrator use?
- Question #16
What network information is required to set up any Cisco switches attached to a clustered Data ONTAP system? (Choose two.)
- Question #17
Click the exhibit button. You are installing a FAS2254 and a DS2246 disk shelf at a customer's site. The controller and disk shelf must be racked in separate rows in the data cente...
- Question #18
You are asked to complete a 2-node installation of a FAS8060 cluster running clustered Data ONTAP 8.3. The hardware has been installed and the cluster has been configured. AutoSupp...
- Question #19
You are performing an installation of a clustered Data ONTAP and you reach the AutoSupport configuration point. You configured AutoSupport with all of the customer's information. B...
- Question #20
A customer wants you to add a disk shelf that contains SSDs so they can implement Flash Pool. Which three tools would you use to complete this task? (Choose three.)
- Question #21
A customer is installing a new system and has determined that they have a broken disk. What information is required to open a NetApp Support case?
- Question #22
You are preparing to install a new 4-node cluster for your customer. They want to use NetApp CN1610 cluster switches that they previously purchased. Which software must be download...
- Question #23
You want to support multiple tenants with duplicate IP addresses for your storage system. Which statement is correct in this scenario?
- Question #24
A customer is using a Cisco Nexus 5020 as a cluster network switch. What would be used as a management network switch in this scenario?
- Question #25
You are planning to install a new clustered Data ONTAP system for a customer. Which action should be performed before configuring the cluster network switches?
- Question #26
A customer wants to graphically manage a new clustered Data ONTAP system. Which tool should the customer use?
- Question #27
What is NetApp's best practice regarding Ethernet flow control?
- Question #28
The full boot cycle of the CN1610 should take approximately 50 seconds. What should you do to minimize the interruption?
- Question #29
Your customer has four disk shelves attached to an HA pair of nodes running clustered Data ONTAP 8.3. One disk shelf has six SSDs and 18 HDDs installed. They want to know how to pa...
- Question #30
Click the Exhibit button. A customer has a 4-node cluster and wants to know what will happen to their data if one of the two HA pairs goes down. Epsilon is configured and working p...
- Question #31
Advanced Drive Partitioning (ADP) is available for which three NetApp systems? (Choose three.)
- Question #32
You are assigned to install two DS2246 shelves, three DS4243 shelves, and one DS4486 shelf. How many rack units (U space) should you account for in this rack layout?
- Question #33
You are installing two disk shelves on an existing clustered Data ONTAP system. One shelf is a DS2246 that matches the other shelves in a stack. The other shelf is also a DS2246 bu...
- Question #34
Upon completion of an installation, you have begun failover/giveback testing. You notice that when node-02 has been taken over by node-01, node-02 will not respond to ping requests...
- Question #35
Which two statements are true regarding SSDs? (Choose two.)
- Question #36
Click the Exhibit button. You are asked to install a new cluster with six FAS8060 nodes. While running Config Advisor, you see the messages shown in the exhibit. The customer does...
- Question #37
A remote administrator is connecting to a cluster from a different remote network. According to NetApp best practices, which type of LIF routing is required to accomplish this task...
- Question #38
You have completed the installation and verification of the cluster for a customer. What is required to complete the event?
- Question #39
You want to install a new clustered Data ONTAP 8.3 system. The customer wants to use open ports on interconnect switches from a different system with clustered Data ONTAP 8.2 becau...
- Question #40
You are planning to update your running switch environment. You need to determine if certain conditions exist before the FASTPATH software and reference configuration file (RCF) on...
- Question #41
You are setting up a LIF for the node management network. What will be the default failover policy in this scenario?
- Question #42
You want to create a data volume on aggr0 and you receive a message with the following warning: ''Warning: You are about to create a volume on a root aggregate. This may cause seve...
- Question #43
You have completed a clustered Data ONTAP installation for a new customer. You are now ready to hand off the system to the customer. Which three actions should you take at this sta...
- Question #44
What happens to the NTP configuration in clustered Data ONTAP 8.3 when a node joins a cluster?
- Question #45
You are assigned to install five DS2246 with twenty-four 400 GB SSDs per shelf to a single node system. According the NetApp, which statement is correct?
- Question #46
Which three types of interface groups are supported on NetApp storage systems? (Choose three.)
- Question #47
You have just configured the customer's first SVM with a LIF IP 10.0.0.10/24. The customer's DNS IP address is 172.16.0.250 and you are unable to ping it from the NetApp storage sy...
- Question #48
You are installing a 4-node cluster with two CN1610 switches. Your co-worker is setting up the switches, but accidentally deletes the current configuration. According to NetApp, wh...
- Question #49
Which switch vendor is supported for the cluster network switches?
- Question #50
According to NetApp, which two scenarios are recommended for a RAID-DP aggregate in clustered Data ONTAP 8.3? (Choose two.)