ISEB-SWT2 Exam Questions
124 real ISEB-SWT2 exam questions with expert-verified answers and explanations. Page 1 of 3.
- Question #1
Which one of the following is true of software development models?
- Question #2
Four testers have each submitted an incident report in which each reported a problem with the User log-on process. User log-on is a critical component of the system. The table belo...
- Question #3
The flow graph below shows the logic of a program for which 100% statement coverage and 100% decision coverage is required on exit from component testing. The following test cases...
- Question #4
Which of the following is a purpose of the review kick off activity?
- Question #5
Which of the following types of defect are typically found in reviews rather than in dynamic testing?
- Question #6
During which activity of the Fundamental Test Process test process do you review the test basis?
- Question #7
How is the scope of maintenance testing assessed?
- Question #8
Which of the following BEST describes a data-driven approach to the use of test execution tools?
- Question #9
From a Testing perspective, what are the MAIN purposes of Configuration Management?
- Question #10
What is the USUAL sequence for performing the following activities during the Fundamental Test Process?
- Question #11
Which of the following statements is true?
- Question #12
Which ADDITIONAL test level could be introduced into a standard V-model after system testing?
- Question #13
The above table shows 6 test procedures (P to U) that must now be entered into a test execution schedule. Business severity is regarded as the most important element in determining...
- Question #14
Which of the following are the typical defects found by static analysis tools?
- Question #15
Which ordering of the list below gives increasing levels of test independence?
- Question #16
Which of the following is a review process activity?
- Question #17
Which one of the following provides the BEST description of test design?
- Question #18
A wholesaler sells printer cartridges. The minimum order quantity is 5. There is a 20% discount for orders of 100 or more printer cartridges. You have been asked to prepare test ca...
- Question #19
Which of the following matches the activity (i to iv) to its most suitable type of tool (p to s)?
- Question #20
A candidate sits an exam with 40 questions. To pass, the candidate must answer at least 25 questions correctly. To gain a distinction, a mark of 32 or above must be achieved. Which...
- Question #21
Consider the following state table: Which of the following would result in a change of state to S2 with an action of R6?
- Question #22
Which of the following are true of software development models?
- Question #23
The below table shows 6 test procedures (P to U) that must now be entered into a test execution schedule. Business severity is regarded as the most important element in determining...
- Question #24
Which of the following statements describe why error guessing is a useful test design technique?
- Question #25
Four testers have each submitted an incident report in which each reported a problem with the User log-on process, a critical component of the system. The incident reports do not f...
- Question #26
Which of the following statements is true?
- Question #27
Which two of the following are common attributes of maintenance testing?
- Question #28
You have designed test cases to provide 100% statement and 100% decision coverage for the following How many MORE test cases are required?
- Question #29
Which of the following is MOST likely to be an objective of a pilot project to introduce a test tool?
- Question #30
Place the stages of the Fundamental Test Process in the usual order (by time).
- Question #31
Which of the following statements about functional testing is correct?
- Question #32
Which of the following defects would NORMALLY be identified by a static analysis tool?
- Question #33
Which of the following activities would improve how a tool is deployed within an organisation?
- Question #34
Given the following sample of pseudo code: Read A, B, C: If A > B then Print Primary ratio is ?& A / B; End If If A > C then Print Secondary ratio is ?& A / C; End If. Which of the...
- Question #35
Which of the following would TYPICALLY be carried out by a test leader and which by a tester?
- Question #36
Which of the following account for most of the failures in a system?
- Question #37
The flow graph below shows the logic of a program for which 100% statement coverage and 100% decision coverage is required on exit from component testing. The following test case h...
- Question #38
Which characteristics BEST describe a walkthrough?
- Question #39
Where may functional testing be performed?
- Question #40
Which of the following are white-box test design techniques?
- Question #41
Which of the following activities should be considered before purchasing a tool for an organization?
- Question #42
Which of the following would NOT NORMALLY be considered for a testing role on a project?
- Question #43
Which statement is a valid explanation as to why black-box test design techniques can be useful?
- Question #44
Why should expected results be defined before execution?
- Question #45
Which of the following software work products would NOT TYPICALLY be examined using static analysis techniques?
- Question #46
A system holds information about an employee; Mike Berry. Which of the following is Mike Berry an example of?
- Question #47
Which of the following statements is TRUE?
- Question #48
Which stage of the Requirements Engineering process is concerned with tracking requirements from inception to implementation?
- Question #49
A process model has been produced which includes diamond-shaped symbols. What does this diamond-shaped symbol represent in the model?
- Question #50
Which of the following statements describe why exploratory testing is a useful test design technique?