HP5-T01D Exam Questions
47 real HP5-T01D exam questions with expert-verified answers and explanations. Page 1 of 1.
- Question #1
How do you boot into Intelligent Provisioning on a ProLiant Gen8 server?
- Question #2
Which memory configuration types are supported in the ProLiant Gen8 server blades? (Select two.)
- Question #3
An administrator must replace a defective processor located in slot 1 in an Intel-based ProLiant DL5860 Gen8 server: What should the administrator do?
- Question #4
An administrator installed HP CS Platinum/Platinum Plus Power Supplies in an enclosure with ProLiant server blades. Which additional components does the administrator need in order...
- Question #5
You need to check the firmware revision of the disk drives installed in a ProLiant DL380Gen8 server. What can you use to check the revision while the server is online?
- Question #6
Which tool can report the amount of life remaining in an HP solid state drive (SSD)?
- Question #7
Where can you verify the status of an external DVD-ROM drive in a c7000 enclosure?
- Question #8
What should be installed on a ProLiant Gen8 server to display operating system information within the iLO 4 GUI?
- Question #9
Which button should you press to enter the RBSU during POST?
- Question #10
Which steps should you perform to save a Virtual Connect configuration?
- Question #11
Why should you use an electrostatic discharge (ESD) wrist strap when replacing parts such as memory DIMMs?
- Question #12
A support engineer needs to add memory to a ProLiant ML350p Gen8 server. What should the engineer consider when selecting the DDR3 DIMMs to install in this server?
- Question #13
Which Virtual Connect module enables FCoE or iSCSI connectivity for BladeSystemserver blades?
- Question #14
How can you verify that the system and option ROMs in a ProLiant server are the latest version?
- Question #15
A customer placed a service call after installing genuine HP memory from a ProLiant DL380 Gen7 server into a new ProLiant DL380 Gen8 server and receiving a POST message that the me...
- Question #16
A customer is experiencing a pre-failure alarm of the battery on a UPS that is almost one year old. Which statement is correct?
- Question #17
If you install two Onboard Administrator modules with different firmware revisions in a c7000 enclosure, which module will be active by default?
- Question #18
You need to capture the configuration and support dump of several Virtual Connect domains. Which tool can you use to perform this action from a central system?
- Question #19
A customer with RAID 1+0 configured in a storage array lost two drives, and the array failed. What should you recommend to address the problem of two simultaneous drive failures?
- Question #20
What are features of the HP ProLiant Micro Server? (Select two.)
- Question #21
How wide must the data center door be to allow an HP MCS G2 rack to be brought into the data center?
- Question #22
An engineer repaired a memory problem in a ProLiant BL460c Gen8 server blade running Windows 2008 R2. What should the engineer do to verify the repair? (Select two)
- Question #23
Where is the data written when power is lost on an HP Smart Array controller?
- Question #24
A support engineer is installing DIMMs of different speeds and voltages in a ProLiant DL380p Gen8 Server. Which rules for DIMM installation must the engineer follow during this ins...
- Question #25
What are some general requirements that must be met to update Virtual Connect firmware? (Select three.)
- Question #26
Which RAID level allows the data to be striped across multiple RAIDs? (Select two.)
- Question #27
A customer needs to remotely monitor the UPS devices on their network They need to send alert traps to HP Systems Insight Manager (HP SIM) and other SNMP management programs and ge...
- Question #28
Which HP tools should you use to determine that an SSD drive has degraded as a result of a large number of write operations? (Select three.)
- Question #29
Which tool can you use to verify that SNMP events appear in HP SIM from a server blade running Windows 2008?
- Question #30
After you replace the system board in ProLiant BL460c GB server blade, the server cannot connect to an external shared storage through the SAS interface. Other similar servers in t...
- Question #31
You replaced a Smart Array P812 in a ProLiant DL380 G7 storage server. What should you do next?
- Question #32
A ProLiant DL380 Gen8 server has become unresponsive several times during the last two weeks. You contacted HP Technical Support and were asked to send them the Active Heath System...
- Question #33
What can an engineer use to ensure quick, precise, intelligent installation when installing CPUs in a ProLiant Gen8 server?
- Question #34
Which memory configuration types are supported in the ProLiant Gen8 server blades? (Select two.)
- Question #35
An HP VC Flex-10 module must be replaced in a c3000 BladeSystem enclosure because one uplink port is defective. What must you do before physically replacing the module?
- Question #36
What can an engineer use to ensure quick, precise, intelligent installation when installing CPUs in a ProLiant Gen8 server?
- Question #37
You are viewing the current driver and firmware status in the Version Control Agent (VCA) and notice that only one column of information is presented. What must you do to see the c...
- Question #38
Which host management solution does HP recommend using with ProLiant Gen8 servers?
- Question #39
A customer has a ProLiant DL380p Gen8 server with one CPU and four 16 GB RDIMMs with 24 total DIMM slots. The customer wants to increase the memory in this server. Which memory opt...
- Question #40
You are troubleshooting a problem with a ProLiant BL460c Gen8 server and need a report detailing the firmware and driver revisions on the server. Which report should you obtain?
- Question #41
A customer placed a service call after installing genuine HP memory from a ProLiant DL380 Gen7 server into a new ProLiant DL380 Gen8 server and receiving a POST message that the me...
- Question #42
Which HP utility can patch a ProLiant server with a release set made up of drivers, firmware, and software that have been tested together?
- Question #43
An engineer repaired a memory problem in a ProLiant BL460c Gen8 server blade running Windows 2008 R2. What should the engineer do to verify the repair? (Select two.)
- Question #44
Which step must be performed after the system board is replaced on a ProLiant BL460c G8 server blade?
- Question #45
What should be installed on a ProLiant Gen8 server to display operating system information within the iLO 4 GUI?
- Question #46
A customer has a c7000 enclosure that is fully populated with ProLiant BL680c server blades. Two months after the initial installation, the rack initiates a thermal shutdown. When...
- Question #47
You replaced a Smart Array P812 in a ProLiant DL380 G7 storage server. What should you do next?