HP2-Z30 Exam Questions

Which statement is correct about IRF?

When performing auto discovery with Intelligent Management Center (IMC), which two components should be defined in order to fully manage the discovered networking devices?

Which HP Comware command saves the startup configuration file to a TFTP server?

Which HP redundancy feature is supported by both HP Provision and HP Comware switches?

Refer to the exhibit. A network administrator has a server currently connected to an access layer switch. The network administrator needs link redundancy for the server and wants t...

Which Intelligent Management Center (IMC) device discovery method is the default for device auto discovery?

Refer to the exhibit. The link aggregation is failing between the HP Provision and HP Comware switches. Which solution solves this problem?

Which HP Comware command can a network administrator execute to view the IP routing table?

Which command defines a default route on an HP Provision switch when routing has been enabled?

Refer to the network exhibit. A user brings a generic switch from home into a company. The user switch does not support any Spanning Tree protocols. The user switch has two connect...

Which configuration tool do HP Provision switches support that HP Comware switches do not support?

Refer to the exhibit. A network administrator is managing the configuration files on an HP Provision switch and executes the commands shown in the exhibit. What is the probable cau...

Which statement is true about using the RADIUS protocol for AAA functions'?

A network administrator receives a new HP Provision switch and notices that the software version running on the switch is older than what is currently used in the network. The netw...

What is the console port designation for an HP Comware switch?

Refer to the network and ARP table exhibit: The user on the left side of the exhibit wants to build a connection to the server on the right. Assume that SwitchA and SwitchB are HP...

A customer must connect networks in two buildings. The buildings are 15 meters apart. The customer does not want the additional cost of installing fiber between the two buildings a...

Refer to the exhibit. A network administrator needs to configure link aggregation using static LACP on Switch-A, which is an HP Comware switch. Which configuration accomplishes thi...

A network administrator has created and applied a configuration to an HP Provision switch. The network administrator then copied the active configuration to a TFTP server. Upon exa...

What are the correct factory default settings when the HP Comware and Provision switches are originally booted?

An administrator is adding an HP Provision switch to an existing OSPF network. The switch has two VLANs, 10 and 20, that should be included in OSPF's area 0. The IP address of the...

What is a key emerging standard protocol that HP Virtual Application Networks (VAN) use to implement Software-Defined Networks (SDN)?

Which protocol only requires MAC addressing?

Which task should a network administrator include in the creation of an upgrade policy?

Which type of access is considered an In-band management connection?

Which HP Comware component allows a network administrator to adjust the logging process?

What must a network administrator define on an HP Comware switch in order to implement username and passwords to protect access to the CLI?

Refer to the network exhibit. All of the switches in the exhibit are configured as follows: Config name =";Region!' Revision #= 1 Instance 1=VLANs 10.12 lnstance2 = VLANs11,13 1ST...

Which action can be performed from an HP Comware switch?

A network administrator executes this command on an HP switch: Provision (config)# vlan 11 untag Al The network administrator immediately realizes that the port that was specified...

Which open-standard protocol allows a network administrator to view the running operating system version and IP address of a neighboring device?

Refer to the partial command output: Based on this output, which statement is true?

Which HP Provision switch command controls the logging level of messages sent to a syslog server?

A network administrator acquires a new HP Comware switch from HP with the factory default settings. The network administrator logs into the console port and configures the followin...

Refer to the network exhibit. Switch_A and Switch_B are HP Comware switches currently in the same MSTP region with the following MSTP configuration: Region name: HP Revision number...

Which console cable is used on an HP Comware switch?

Which FlexArchitecture component uses Virtual Connect in blade server systems?

Which HP ProVision and HP Comware commands restore a configuration file from a TFTP server to the switches' flash? (Select two.)?

Which IRF configuration, in the correct order, includes the physical interfaces in an IRF port?

Which Software-Defined Network (SDN) layer includes HP Provision and HP Comware switches?

What is the default username and password an administrator would use to log into a new HP MSM access point?

Which Intelligent Management Center (IMC) group role allows an administrator to manage networking devices, but cannot add new IMC administrative users?

Which Layer 2 mechanism should be used to authenticate wireless or wired users before allowing them access to network resources?

Which HP switch supports nine switches in an IRF topology?

Refer to the network exhibit. Assume the network shown in the exhibit has implemented RSTP Based on the topology, which port is a root port?

Which component of an HP Comware switch controls logging on to a syslog server?

Which Access Point (AP) type corresponds to HP MSM autonomous operational mode?

Which statement is true about spanning tree and HP Comware and HP Provision switches?

Which VLAN port type is only supported by HP Comware switches?

Which HP ProVision switch command defines 10.1.1.1 as a syslog server?