HP0-Y52 Exam Questions

Which method of link aggregation do both HP ProVision and Comware switches support?

A company needs a two-member Intelligent Resilient Framework (IRF) virtual switch. The network administrator is configuring IRF member 2 that will connect to port 1/1 on IRF member...

A network administrator wants an HP switch to use an IP address that is always up for its Open Shortest Path First (OSPF) router ID. Which address meets this requirement?

Refer to the exhibit. The network administrator has configured this port to permit all VLANs. The output in the exhibit indicates that the port is only passing VLANs 1 and 11. The...

Refer to the exhibit. Switch-1 is an HP ProVision switch. A network administrator wants Switch-1 to run Open Shortest Path First (OSPF) and create neighbor relationship on Links 1...

Which HP software platform provides centralized network management, monitoring, and configuration of wired and wireless network infrastructure devices, as well as traffic monitorin...

Refer to the exhibit. The exhibit shows partial output of the HP Comwaredisplay ip routing-table command. Note thePreorpreferencecolumn. On an HP ProVision switch, what is the corr...

An administrator is configuring OSPF on an HP ProVision switch. What is one of the steps that the administrator must take?

Refer to the exhibit. Which endpoint or endpoints receive broadcast ARP requests sent by EndpointA?

A tagged frame arrives on a switch port that is not a tagged member of the VLAN indicated by the frame ID. What do fundamental VLAN operating rules require the switch to do with th...

How does Open Shortest Path First (OSPF) help enterprises meet their high availability requirements, compared to RIP?

A customer has an HP ProVision switch capable of Layer 3 forwarding: however, Layer 3 forwarding is disabled. The switch has an IP address in the management VLAN, where the default...

Refer to the exhibit. A network administrator has implemented link aggregation on an HP Comware switch using LACP. The two ports are functioning at the data link layer between the...

What is the maximum number of active links supported between a device and HP ProVision switches when distributed trunking is used to connect the device to the ProVision switches?

All of the switches in Exhibit 1 are routing switches. Exhibit 2 shows the routes configured on these switches. The direct (connected) routes are not shown, but assume that links a...

Which credential is required to validate SNMPv2c write requests?

A customer is implementing an access layer solution with four HP Comware switches in an Intelligent Resilient Framework (IRF) virtual device or domain. The customer expects to add...

Which term refers to aggregated links on HP ProVision switches?

Which ProVision configuration includes 10.0.3.0/24, which represents VLAN 30 in OSPF area 0?

Refer to Exhibit. The server shown in the exhibit requires redundant links, and The link aggregation should use LACP. What should the administrator configure on the 1RF virtual swi...

Two switches are members in an active Intelligent Resilient Framework (IRF) virtual device. A network administrator joins a third switch to the IRF virtual device. Which switch is...

Which command can a network administrator execute on an HP Comware switch to manage configuration files?

Which statement is true about wireless technologies?

A network administrator configures this command on an HP ProVision switch: vlan 30 ip helper-address 10.0.3.253 The switch is able to ping 10.0.3.253. After the administrator confi...

What is the purpose of a management VLAN on an HP Provision switch?

Refer to the Exhibit. A network administrator needs to configure DHCP on SwitchA. Assume that SwitchA is an HPE Comware switch and is using the default settings for DHCP. The admin...

Refer to the Exhibit. Exhibit: HP Comware switch configuration. [Comware] vlan 100 [Comware-vlan100] quit [Comware] vlan 200 [Comware-vlan200] quit [Comware] interface g1/0/22 [Com...

An HP Provision switch has port A1 connected to port g1/0/1 of an HP Comware switch. The ProVision port has the following configuration: vlan 1 untag A1 vlan 10 tag A1 vlan 20 tag...

Refer to the Exhibit. Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2. How does this affect the Multipl...

A network administrator enters this command on an HP Comware switch: <Comware> save In interactive mode, the administrator is prompted to save to a file named config.cfg and confir...

An HP ProVision switch is operating at its factory default settings. A network administrator connects the switch to a VLAN with a DHCP server. The switch-to-switch connection is ca...

Refer to the exhibit. A network administrator is upgrading the operating system on an HP Comware switch. When copying the new image from a TFTP server to the flash of the switch, t...

On an HP Comware switch, which view must an administrator access in order to execute the debug command?

Which HP device or port type can modify, read, and respond with frames that include 802.1Q VLAN tags?

Refer to the exhibit. What can a network administrator determine from the output in the exhibit?

A company wants a modular switch for the access layer at its main campus and for several branch offices. Which HP Switch Series is best suited for this role?

A server connects to a port on an HP Comware switch. The network administrator wants to ensure that: - the port remains forwarding during Multiple Spanning Tree Protocol (MSTP) top...

Which HP solution delivers automated virtual machine orchestrator, automatic synchronization of network connectivity information, and visibility to performance of wired and wireles...

Refer to the exhibit. Assume that Student A's ARP table is empty. Student A is preparing to send an FTP packet to FTP Server B and needs to discover the proper destination MAC addr...

Which statement is true concerning spanning tree protocols and HP switches?

A network administrator enters this command on an HP ProVision switch with IP routing enabled: ip route 0.0.0.0/0 10.1.1.1 metric 10 distance 10 This is the only IP route to 0.0.0....

Refer to the exhibit. A network administrator enters the command shown in the exhibit to check the VLANs on an HP ProVision switch interface. The administrator wants to discover wh...

A customer is implementing a network using HP ProVision switches. Which default setting applies to the ProVision switches?

An HP Comware switch should send messages to an SNMP server when various events occur. What is one step in the configuration of this feature?

An HP switch learns identical valid routes with different protocols. How does the switch choose which route to add to its IP routing table?

What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)?

A network administrator wants to disable physical interfaces 13-24 on an HP ProVision switch. How can the administrator do this?

What is a valid reason to choose an 802.11a wireless implementation?

Which statement correctly defines the management capabilities of an HP MultiService Mobility (MSM) access point (AP)?

When adding a new member to an existing IRF domain, which of the following must you perform first?