E20-690 Exam Questions

Using the Unisphere Storage System Initialization Wizard, what are valid data port network parameters for iSCSI connectivity on a VNX for Block system?

When installing a new VNX Gateway system, which utility or tool can be used to install the VNX OE for File software?

When installing a VNX for File, which subnet must be used?

What is required to run VIA from a service laptop when configuring a VNX system?

What is VIA used to configure?

You are required to install ESRS on a newly installed VNX for Block array. Where can the latest version of the VNX Installation Toolbox be located?

Which type of connection does the Control Station use for management?

What are the Alert Severity Types?

You plan to collect an SPCollect and log files from the storage system in USM using the Capture Diagnostic Wizard. How should this be run?

In a VNX Gateway environment, what is referred to as the "front end"?

What software is required for a VNX VG10 installation?

How is a storage subsystem connected to a VNX Gateway in a direct-attached environment?

On the VNX Gateway platform, which I/O module slot and FC ports are reserved for tape devices?

Which condition must be met before starting the Unisphere Storage System Initialization Utility?

Which condition must be met before starting the Unisphere Storage System Initialization Utility?

Which protocols does the Storage System Initialization Wizard use to discover an uninitialized VNX?

What is the default VNX Unified storage system name?

You are installing multiple VNX arrays, and find that the different arrays share the same serial number. What will be the result?

What is a function of the ESRS Management Utility?

What is a function of the ESRS Management Utility?

You want to verify that a storage array is configured as a Unified, File or Block. Where can the storage type be determined?

Where can documentation for installing and set up of the ESRS IPclient suite be found?

You are changing the SP hostnames using the storage system Initialization Wizard. What message will be displayed?

You are adding two DAEs: one 15-drive and one 25-drive. What are the advantages of cabling the additional DAEs so that one is added to SAS 0 and one is added to SAS 1?

While at a customer's site, you need access to a VNX Storage Processor on IP address 10.11.12.13. You want to use RemotelyAnywhere but https://10.11.12.13 does not open the login s...

In which folder can the SPcollects be found when accessing a storage processor through Remotely Anywhere?

You are an EMC service provider and want to install the ESRS IP client solution. The workstation on which you want to install this software is on a network with a proxy server. Wha...

You are installing an ESRS IP Client to monitor a VNX Block array. You also want to connect remotely to SP A and SP B over the ESRS platform. What needs to be done first?

What file is created on the storage processor by the TRT process during analysis of an event?

What components are prerequisites for UDoctor?

What does UDoctor analyze to determine if an alert needs to be dialed home to EMC?

Which component is configured and used to send a regularly scheduled event to SYR to test connectivity?

Which component of ESRS-IP solution is responsible for event-based detection and alert notification?

You are collecting logs from a VNX Control Station. What is a function of the following command? $ /nas/tools/automaticcollection -getlogs

Which reason codes will a healthy VNX for File primary Control Station and Data Movers display with the / nas/sbin/getreason command?

What reason code will a healthy VNX with dual control station and two data movers display with the /nas/ sbin/getreason command?

You are onsite to replace a faulted Data Mover. After the faulted Data Mover has been physically replaced, which command will return the primary Data Mover back to an active state?

A VNX migration is planned. You go on site to start the manual log collection script. What command would you use to start this script?

You have completed a VNX Unified installation and are now verifying the configuration. You notice that the ConnectHome configuration is incorrect. You attempt to correct parameters...

You are on-site, servicing a VNX with MCx hardware without the use of ethernet. What are the correct terminal settings for utilizing the serial port?

You are tasked with connecting to a VNX with MCx, but are unsure of the customer's public network IP address for the storage processor. Which factory-set IP addresses can be used t...

You are auditing active software enablers and currently installed software packages on a VNX with MCx array. Which command will assist in this task?

What does the naviseccli managefiles command with the -list function display?

Dump files are needed from a Storage Processor. Which naviseccli managefiles command option will accomplish this?

You are performing a non-disruptive upgrade. However, end-users are reporting that they cannot access data while you are performing the operation. What could be the issue?

On which LUN will SP software driver packages be transferred when using the NDU command?

You are preparing for a VNX Unified upgrade. What needs to be performed to determine the health status and the estimated time the upgrade will take?

After which step during an NDU upgrade can the process no longer be aborted?

What tool must run and complete successfully before a VNX file upgrade can be done?

By default, how does USM install new VNX OE software for Block and File?