E20-611 Exam Questions

SP Collect is initiated by right clicking on a SP. Where does script execute?

A CLARiiON Array has 15 FC 36GB drives, 15 FC 73GB drives, 15 ATA 320GB drives and 15 ATA 250 GB. What is the minimum number of Hot Spares you should have?

What is the output file extension for SPLAT2?

You are upgrading a customer's CLARiiON Array from Flare 16 to Flare 19. What are two [2] options to perform this?

You were asked to gather host information. Which UNIX host based utility does EMC provide to gather this information?

Which CLARiiON Array software component must be installed and active to enable the GUI?

CAP2 requires 128 MB RAM to run. What are two other requirements to run CAP2?

Which node should be the master node when managing a domain with CLARiiON Arrays at different code levels?

What is a restriction when using the CLARiiON Array initialization Wizard?

What is one way to transfer a recovery image?

You have a CX700 with Release 16 Flare. After the completion of a revert procedure, you need to upgrade the code to the customer's approved level. You cannot access the array's Man...

During a CLARiiON management station installation, EMCRemote is unable to communicate with the SP. What is the most likely reason?

How many power supply fans are required to allow a CX700 SPE to remain powered up?

Which tool will gather array configuration and basic health conditions for troubleshooting, site audits, health checks and Enhanced Install Procedures?

What are the output file extensions for FBI and for Navisphere Analyzer?

You need to assign a LUN to more than one Storage Group. Which options under Show LUNs do you use?

You are troubleshooting a CLARiiON Array running Release 16. Which command is used to gather information from the Storage Processors?

Which two [2] cache types are required on a CLARiiON Array to achieve optimal host data flow performance?

Which syntax switch is replaced by -address in Navisphere Secure CLI?

What data does EMCGrab collect?

What is the maximum number of initiators per sp port on a CX700 CLARiiON Array?

After running a SP Collect, which file is sent to Tech Support?

SPLAT2 indicates 98 soft-SCSI-errors per day on an ATA LUN of a CX400. Which action should be taken?

Which three [3] optional host failover software are supported with NDU?

How many fans within the three hot swop-able fan packs are required to allow a CX700 SPE to remain powered up?

Which tool is used to analyze EMCGrab output?

On a CX700, WWN 50:06:01:69:90:60:05:e4 matches to which Storage Processor port?

Which tab displays specific error counts in CAP2?

You are sent a DPE with 15 drives for an install. Which two CLARiiON CX-series models apply?

You are troubleshooting a CLARiiON Array with SPLAT2. You are having problems with the analyze function. What is the cause?

You issue the following command: naviseccli -h ss1_spa createrg 3 0_0_9 The command fails. Why did the command fail?

Under which three [3] conditions is Engineering Mode used to perform an NDU?

The event log of a CLARiiON CX600 Array has displayed the following error message: 09/26/05 18:10:49 Bus1 Enc4 Dsk5 820 Soft Media Error 5 0 0 Which explanation should be provided...

Which tool is used to analyze EMCReports output?

Why does SPLAT2 need a SP Collect from both SPs for troubleshooting problems?

Which statement is true about the effective use of Analyze-function in SPLAT2?

Which two [2] CLARiiON Array based tools do you have access to in a CX700 with Release 19?

The customer requires real-time synchronous off-site disaster recovery. Which CLARiiON layered application meets this requirement?

How many CMI channels are available in a CLARiiON CX3-80?

In a CLARiiON CX3 series array, how many LUNs can be defined within a RAID 1/0 group?

Which two CLARiiON array-based tools do you have access to in a CX700 with release 19?

At release 22, which package is a Non-Disruptive Upgrade bundle for a CLARiiON CX3-80 currently running?

How many back-end ports are on each CLARiiON CX3-40f SP?

In the FLARE database, what identifies the location of the LUN to which the disk is bound, the LIC revision used to bind the disk, and the slot and enclosure address that the drive...

Which applications will be installed by the CLARalert Remote Service CD?

Where is the SPA I/O module 0 located?

In CAP2, which tab displays the error counts?

Which RAID type distributes parity across each drive in the RAID group?

If the Link Status LED on a DAE3P LCC is blue, what is the link speed?

Company.com Engineer is dispatched to Company.com site to install a new CLARiiON CX3-80. The CE begins by running the Enhanced Install Procedure (EIP). What is the first step perfo...