E20-377 Exam Questions
328 real E20-377 exam questions with expert-verified answers and explanations. Page 3 of 7.
- Question #103
You are implementing a RecoverPoint solution using SANTap splitters. After configuring SANTap on the MDS switch, you try to add the splitter into RecoverPoint. The splitter is not...
- Question #104
What is the architectural difference between the Symmetrix VMAXe splitter and any other splitter type?
- Question #105
Which process runs on the RPA selected as the leader of the cluster?
- Question #106
In which replication mode does the RPA save data in cache memory when marking data?
- Question #107
A customer is planning to install two RecoverPoint clusters sharing a VNX splitter. What is a consideration for this environment?
- Question #109
A customer has implemented their CLARiiON using both FC and iSCSI-attached devices. They are considering deploying RecoverPoint with the VNX/CLARiiON splitter. Which devices are su...
- Question #110
What accurately describes an EMC RecoverPoint cluster?
- Question #111
A customer environment requires 136 consistency groups in a CDP environment. The customer has purchased eight RPAs and wants to implement RecoverPoint. Which environment would you...
- Question #112
A customer's security team has asked you to delete all of the built-in UserIDs after you successfully setup authentication to their LDAP servers. What is the best way to accomplish...
- Question #113
What are the required zone members when configuring frame redirect mode for reservation support?
- Question #114
You are planning a SANTap splitter deployment. The customer wants to know the benefit of updating the SAN hardware from SSM to MSM cards. Based on performance, what is the primary...
- Question #115
As part of your RecoverPoint planning and design, you have just completed change rate analysis, RPO, and RTO to size journal capacity. In addition to capacity of the journals, you...
- Question #116
You are preparing to start the installation of the RPAs for a customer. What are two methods to connect to the RecoverPoint Appliances?
- Question #117
A customer has mirrored fabrics running SANTap on their MDS-9513s using SSM modules. They have a new requirement for 498 fabric ports per MDS-9513. What is a solution without addin...
- Question #118
Refer to the Exhibit. You are upgrading the Brocade splitter on an AP-7600B. During the preparation phase, you check the blade processor to make sure the upgrade will complete succ...
- Question #119
An administrator would like to perform periodic testing of replica images. The validation will mainly consist of checksums of files on the replica compared to the source. The admin...
- Question #120
You are planning to deploy SANTap with Emulex HBAs. Which possible host changes must you consider?
- Question #121
A customer wants to activate iDRAC for their RecoverPoint environment for remote monitoring and support. Which port on Gen4 RPAs is configured with an extra MAC address to handle t...
- Question #123
A customer is planning to add RecoverPoint to an existing VNX/CLARiiON MirrorView implementation. Which zoning configuration must be considered?
- Question #124
You have a customer that has four RPA clusters sharing a VNX splitter. They would like to configure 512, 1024, 256, and 512 LUNs per cluster respectively. How would you advise the...
- Question #125
A customer has expressed an issue about the consistency group performance on an RPA . They would like to know the best way to optimize the system. Which command will provide the cu...
- Question #126
In addition to Host ITLs, which other ITLs do you need to keep track of in a SANTap environment?
- Question #127
Which SAN configuration entities must be created in the fabric when implementing an IBM AIX host splitter?
- Question #128
Which generation of RecoverPoint Appliance hardware must be used to ensure you can use a CRR over FC configuration?
- Question #129
You want to upgrade a RecoverPoint environment using Deployment Manager (DM). As a prerequisite to continuing with the upgrade, which TCP port needs to be open between the manageme...
- Question #130
A journal volume is being sized. The customer environment requires a rollback capability of 48 hours and shows a Write rate of 4 Mb/s to the volumes that make up a consistency grou...
- Question #131
You are installing the RecoverPoint splitter agent on a B-Series switch. After downloading the agent binary file to the blade processor, which step must be completed prior to succe...
- Question #132
You have a customer with an EMC VNX array at each site that uses both block and file storage. They would like to use the VNX splitter to replicate all their iSCSI data LUNs. How wo...
- Question #134
What is a RecoverPoint design consideration for the replication volumes in a heterogeneous storage environment using a fabric splitter?
- Question #135
Refer to the Exhibit. You are troubleshooting a RecoverPoint issue where consistency groups, using a kdriver splitter, have stopped working. While analyzing the problem, you ran de...
- Question #136
A customer needs to change the Backlog Mirroring configuration parameters for RecoverPoint. RecoverPoint is using a Symmetrix splitter. How can this change be completed?
- Question #137
Which VSAN should storage ports be a member of in a SANTap environment?
- Question #139
During Consistency Group initialization, the host application experiences a performance impact. What can be used to reduce the negative impact on performance?
- Question #140
Which RecoverPoint CLI command would you run to get the errors and warnings for one cluster or for the entire environment?
- Question #141
Which statement is true regarding vRPAs?
- Question #142
After selecting a cluster in the RPA Clusters tab, which option can display alerts that have been logged for any of the physical components of the RecoverPoint system in that clust...
- Question #143
You are concerned about the performance of the RecoverPoint replication. Some of the Consistency Groups continue to go into High Load. Initial troubleshooting points to a data comp...
- Question #144
An administrator performs a Consistency Group failover to a remote cluster. What happens to the data stored in the copy journal after the copy journal becomes the production journa...
- Question #145
You are implementing a RecoverPoint/SE cluster using vRPAs. What must be configured and available on the new VNX array prior to the installation of the cluster with Deployment Mana...
- Question #146
When adding a new vRPA, what is the only storage authentication method that is supported?
- Question #147
A VPLEX write splitter can be shared with how many RecoverPoint clusters?
- Question #148
Which type of Consistency Group requires a primary and secondary production copy?
- Question #149
Which FA ports must the production LUN be mapped to in order to perform write splitting using the VMAX splitter?
- Question #150
When registering the RPA with a VNX to enable a VNX splitter for RecoverPoint, what failover mode must be set on the VNX?
- Question #151
A customer environment uses VMAX arrays for production storage. The customer wants to implement RecoverPoint for data protection. Having researched vRPAs, they want to use this tec...
- Question #152
What is a possible trigger to initiate RecoverPoint Snap-based Replication?
- Question #153
Which ports from a VPLEX Metro system must be zoned to the RPAs in order to install the VPLEX write splitter?
- Question #154
Which tool do you need in order to run the save_settings command from a Windows command prompt?
- Question #155
You are responsible for installing a four-node RPA cluster. All RPAs are powered on. Both the FC and IP networks are connected, zoned, and routed properly. The RPAs are loaded with...
- Question #156
A VMware user is currently protecting their virtual application servers with RecoverPoint. All data is stored on two VNX arrays. They will soon be adding Site Recovery Manager (SRM...