E20-335 Exam Questions
221 real E20-335 exam questions with expert-verified answers and explanations. Page 1 of 5.
- Question #1
In symmetric V-max series array running Enginuity 5874, which device is used as a pass-through device for Auto provisioning?
- Question #2
A customer needs to comply with data-at-rest security on a server connected to a Symmetrix. Which security feature will satisfy those requirements?
- Question #3
During an initial implementation of symacl, the service processor was set up with an administrative group. In addition, an access ID PIN was entered on the Symmetrix. What is the n...
- Question #4
What is recommended before creating a TimeFinder/Mirror replica?
- Question #5
Diagnostic messaging for the GNS daemon is written to which file?
- Question #6
What is another possible scheme for RAID 6 for a Symmetric V-max besides 6+2?
- Question #7
During the testing of an Open Respirator implementation the create operation failed. One of the lines in the SYMAP1 log file has the following entry SANCOPY_DEV_TARGET_TOO SMALL Wh...
- Question #8
How do you examine the attribute of a Dynamic SRDF device?
- Question #9
Which of these protection types offers the best protection?
- Question #10
In a single hop SRDF/AR setup the options have been set as follows Cycle time-300 Delay Time-200 Overflow: Next The symreplicate session was started at time 0. The actual cycle was...
- Question #11
What is the advisable Meta structure in a Virtual Provisioning environment?
- Question #12
Which device types are used when using SMC to create devices for virtual Provisioning?
- Question #13
How does Enginuity Consistency Assist (ECA) differ from power path?
- Question #14
How does TimeFinder emulation mode convert commands?
- Question #15
What is the state of the standard and BCV devices after a full TimeFinder/Mirror "Establish" has been initiated?
- Question #16
A SMC user must have the ability to create new SMC users and assign permission. This user should not have any Symmetric configuration or replication privileges. Which role should b...
- Question #17
Which Open Replicator operations can be incremental?
- Question #18
What is the maximum number of initiators allowed in a Symmetrix V-Max array initiator Group?
- Question #19
When the first device added to a thin pool RAID, which other types of protected devices can be added to the same thin pool?
- Question #20
Which statement describes TimeFinder/Clone technologies?
- Question #21
Refer to the exhibit. You are in the process of implementing Symmetrix Management Console in the configuration shown in the exhibit Server A can access Server B over an IP network,...
- Question #22
Which UNIX utility or tool would you use to perform an IBM-AIX host-based data migration?
- Question #23
What is the maximum number of TimeFinder/Snap sessions that can be created from a single source?
- Question #24
When installing Enabler on a Windows server, what will the SYMRECOVER component provide?
- Question #25
Multiple RDF groups from Different Symmetric arrays have been grouped together to enable Multi Sessions consistency. How does Cycle Switching occur in this configuration?
- Question #26
What is the maximum volume size configurable on a V-Max?
- Question #27
Refer to the exhibit. Which delta set will be discarded as a result of a Multi session-Consistency (MSC) cleanups?
- Question #28
Question statement missing
- Question #29
Which feature allows the contents of a BCV to remain unchanged during and after operation? Even while the BCV and the standard is synchronized?
- Question #30
What is an advantage of using thin provisioning?
- Question #31
The customer has built the necessary infrastructure at the remote site for application. What is the primary impact to the customer of a single hop SRDF/ AR solution when compared t...
- Question #32
Which replication operations are supported by Solution Enabler SYMCLI, but NOT by Symmetrix management console?
- Question #33
A customer wants to deploy SRDF/S between a pair of Symmetrix V-Max arrays. The R1-R2 devices will be RAID 1 protected. Two RAID 1 BCVs will be currently established with the R1 de...
- Question #34
What is a requirement for implementing SRDF in a Virtual Provisioning environment?
- Question #35
With the DMX-3 and DMX4, where is the VCM database stored?
- Question #36
Under which condition will Enquiry remove the Consistency Exempt attribute from the RDF mirror?
- Question #37
Refer to the Exhibit. Server A and Server B are running two different applications on SRDF R1 devices on the Source Symmetrix. All the R1 devices belong to the same RDF group. Both...
- Question #38
A customer has implemented a symclone create command with the pre copy option. The clone session was than activated. At this point what is the state of the clone target device?
- Question #39
What is suppressed when scripting SYMCU commands using the -nop option?
- Question #40
After acquiring a company 300 hundred miles from their current office the customer has asked EMC to help to design a single hop application recovery plan after careful analysis of...
- Question #41
A customer is in the process of implementing a TimeFinder/Clone solution. What is the maximum number of differential copies of a single standard source device?
- Question #42
What state should the BCV be in for it to be accessed by a host?
- Question #43
Refer to the Exhibit. A Symmetrix is configured with the two RDF Groups RDFG 1 and RDFG 2 as shown. The SRDF R1 devices used by Application (App 1) are in RDFG 1. The SRDF R1 devic...
- Question #44
A Symmetrix management Console user has been asked to configure Replication mirror. Which Replication Models can be enabled?
- Question #45
In order for thin provisioning to work, what should also be done in addition to providing thin and data (thin pool) devices?
- Question #46
Which replication product can be used to create point-in-Time copies of thin devices to other thin devices?
- Question #47
What status of Time Finder/Snap virtual devices will be used as a control device in an Open replicator implementation devices?
- Question #48
What is the result of one or more source (R1) devices in an SRDF/S consistency group cannot propagate data to their corresponding target (R2) devices?
- Question #49
Which two TimeFinder/Clone actions are initiated when issuing a Symclone establish command?
- Question #50
What are the recommended applications to bind and unbind thin devices from a pool?